OPERATIONAL MODES SOFTWARE WATCHDOG IN STOP" />
參數資料
型號： MC33889DDW
廠商： Freescale Semiconductor
文件頁數： 21/59頁
文件大?。?/td> 0K
描述： IC SYSTEM BASE W/CAN 28-SOIC
標準包裝： 26
控制器類型： 系統基礎芯片
接口： CAN
電源電壓： 5.5 V ~ 18 V
電流 - 電源： 45mA
工作溫度： -40°C ~ 125°C
安裝類型： 表面貼裝
封裝/外殼： 28-SOIC（0.295"，7.50mm 寬）
供應商設備封裝： 28-SOIC W
包裝： 管件
Analog Integrated Circuit Device Data
28
Freescale Semiconductor
33889
FUNCTIONAL DEVICE OPERATION
OPERATIONAL MODES
SOFTWARE WATCHDOG IN STOP MODE
If the watchdog is enabled (register MCR, bit WDSTOP set), the MCU has to wake-up independently of the SBC before the
end of the SBC watchdog time. In order to do this, the MCU has to signal the wake-up to the SBC through the SPI wake-up (CS
pin low to high transition to activated the SPI wake-up). Then the SBC wakes up and jumps into the normal request mode. The
MCU has to configure the SBC to go to either into normal or standby mode. The MCU can then choose to go back into stop mode.
If no MCU wake-up occurs within the watchdog timing, the SBC will activate the reset pin and jump into the normal request
mode. The MCU can then be initialized.
NORMAL REQUEST MODE
This is a temporary mode automatically accessed by the device after a wake-up event from sleep or stop mode, or after device
power up. In this mode, the VDD1 regulator is ON, V2 is off, and the reset pin is high. As soon as the device enters the normal
request mode, an internal 350 ms timer is started. During these 350 ms, the microcontroller of the application must address the
SBC via the SPI and configure the watchdog register (TIM1 register). This is the condition for the SBC to leave the Normal request
Mode and enter the Normal mode, and to set the watchdog timer according to the configuration done during the Normal Request
mode.
The “BATFAIL flag” is a bit which is triggered when VSUP falls below 3.0 V. This bit is set into the MCR register. It is reset by
the MCR register read.
INTERNAL CLOCK
This device has an internal clock used to generate all timings (reset, watchdog, cyclic wake-up, filtering time etc...).
RESET PIN
A reset output is available in order to reset the microcontroller. Reset causes are:
VDD1 falling out of range: if VDD1 falls below the reset threshold (parameter RST-TH), the reset pin is pulled low until VDD1 returns
to the nominal voltage.
Power on reset: at device power on or at device wake-up from sleep mode, the reset is maintained low until VDD1 is within its
operation range.
Watchdog timeout: if the watchdog is not cleared, the SBC will pull the reset pin low for the duration of the reset duration time
(parameter: RESET-DUR).
For debug purposes at 25 °C, the reset pin can be shorted to 5.0 V.
SOFTWARE WATCHDOG (SELECTABLE WINDOW OR TIMEOUT WATCHDOG)
The software watchdog is used in the SBC normal and stand-by modes for monitoring the MCU. The watchdog can be either
a window or timeout. This is selectable by the SPI (register TIM, bit WDW). Default is the window watchdog. The period of the
watchdog is selectable by the SPI from 5.0 to 350 ms (register TIM, bits WDT0 and WDT1). When the window watchdog is
selected, the closed window is the first half of the selected period, and the open window is the second half of the period. The
watchdog can only be cleared within the open window time. An attempt to clear the watchdog in the closed window will generate
a reset. The Watchdog is cleared through the SPI by addressing the TIM register.
Refer to ”table for reset pin operations” operation in mode 2.
WAKE-UP CAPABILITIES
Several wake-up capabilities are available for the device when it is in sleep or stop mode. When a wake-up has occurred, the
wake-up event is stored into the WUR or CAN registers. The MCU can then access the wake-up source. The wake-up options
are selectable through the SPI while the device is in normal or standby mode, and prior to entering low power mode (Sleep or
Stop mode).
WAKE-UP FROM WAKE-UP INPUTS (L0, L1) WITHOUT CYCLIC SENSE
The wake-up lines are dedicated to sense external switch states, and when changes occur to wake-up the MCU (In sleep or
stop modes). The wake-up pins are able to handle 40 V DC. The internal threshold is 3.0 V typical, and these inputs can be used
as an input port expander. The wake-up inputs state can be read through the SPI (register WUR). L0 has a lower threshold than
L1 in order to allow a connection and wake-up from a digital output such as a CAN physical interface.
相關PDF資料
PDF描述
PIC16C712-04I/P IC MCU OTP 1KX14 A/D PWM 18DIP
MC33889DWR2 IC SYSTEM BASE W/CAN 28-SOIC
MC33889DDWR2 IC SYSTEM BASE W/CAN 28-SOIC
MCZ33399EFR2 IC LIN INTERFACE W/WAKE 8-SOIC
MC33389CDHR2 IC SYSTEM BASE W/CAN 20-HSOP
相關代理商/技術參數
參數描述
MC33889DDWR2 功能描述:網絡控制器與處理器 IC SBC LIGHT REV D RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
MC33889DEG 功能描述:IC SYSTEM BASE W/CAN 28-SOIC RoHS:是 類別:集成電路 (IC) >> 接口 - 控制器 系列:- 標準包裝:4,900 系列:- 控制器類型:USB 2.0 控制器 接口:串行 電源電壓:3 V ~ 3.6 V 電流 - 電源:135mA 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:36-VFQFN 裸露焊盤 供應商設備封裝:36-QFN（6x6） 包裝:* 其它名稱:Q6396337A
MC33889DPEG 功能描述:CAN 接口集成電路 SBC-LITE-LS-CAN RoHS:否 制造商:Texas Instruments 類型:Transceivers 工作電源電壓:5 V 電源電流: 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:SOIC-8 封裝:Tube
MC33889DPEGR2 功能描述:CAN 接口集成電路 SBC-LITE-LS-CAN RoHS:否 制造商:Texas Instruments 類型:Transceivers 工作電源電壓:5 V 電源電流: 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:SOIC-8 封裝:Tube
MC33889DW 功能描述:IC SYSTEM BASE W/CAN 28-SOIC RoHS:否 類別:集成電路 (IC) >> 接口 - 控制器 系列:- 標準包裝:4,900 系列:- 控制器類型:USB 2.0 控制器 接口:串行 電源電壓:3 V ~ 3.6 V 電流 - 電源:135mA 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:36-VFQFN 裸露焊盤 供應商設備封裝:36-QFN（6x6） 包裝:* 其它名稱:Q6396337A
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*