- 您現在的位置：買賣IC網 > PDF目錄11649 > MC33794EK (Freescale Semiconductor)IC SENSOR ELECTRIC FIELD 54SOICW PDF資料下載
參數資料
| 型號： | MC33794EK |
| 廠商： | Freescale Semiconductor |
| 文件頁數： | 13/18頁 |
| 文件大小： | 0K |
| 描述： | IC SENSOR ELECTRIC FIELD 54SOICW |
| 產品目錄繪圖： | MC33794EK(R2) Top MC33794EK(R2) Side |
| 標準包裝： | 26 |
| 類型： | 傳感器接口 |
| 輸入類型： | 邏輯 |
| 輸出類型： | 邏輯 |
| 接口： | ISO9141 |
| 電流 - 電源： | 7mA |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 54-BSSOP（0.295"，7.50mm 寬）裸露焊盤 |
| 供應商設備封裝： | 54-SOIC W EP |
| 包裝： | 管件 |
Sensors
4
Freescale Semiconductor
MC33794
8
LAMP_SENSE
Lamp Sense
This terminal is normally connected to the LAMP_OUT terminal. The voltage at
this terminal is reduced and sent to LAMP_MON so the voltage at the lamp
terminal is brought into the range of the analog-to-digital converter (ADC) in the
MCU.
9
LAMP_MON
Lamp Monitor
This terminal is connected through a voltage divider to the LAMP_SENSE
terminal. The voltage divider scales the voltage at this terminal so that battery
voltage present when the lamp is off is scaled to the range of the MCU ADC.
With the lamp off, this terminal will be very close to battery voltage if the lamp is
not burned out and the terminal is not shorted to ground. This is useful as a lamp
check.
10
SHIELD_EN
Shield Driver
This terminal is used to enable the shield signal. The shield is disabled when
SHIELD_EN is a logic low (ground)
11–14
A, B, C, D
Selector Inputs
These input terminals control which electrode or reference is active. Selection
values are shown in Table 5, Electrode Selection, page 10. These are logic level
inputs.
15
SIGNAL
Undetected Signal
This is the undetected signal being applied to the detector. It has a DC level with
the low radio frequency signal superimposed on it. Care must be taken to
minimize DC loading of this signal. A shift of DC will change the center point of
the signal and adversely affect the detection of the signal.
16
LEVEL
Detected Level
This is the detected, amplified, and offset representation of the signal voltage on
the selected electrode. Filtering of the rectified signal is performed by a capacitor
attached to LP_CAP.
17
PWR_MON
Power Monitor
This is connected through a voltage divider to VPWR. It allows reduction of the
voltage so it will fall within the range of the ADC on the MCU.
18
LP_CAP
Low-Pass Filter Capacitor
A capacitor on this terminal forms a low pass filter with the internal series
resistance from the detector to this terminal. This terminal can be used to
determine the detected level before amplification or offset is applied. A 10 nF
capacitor connected to this terminal will smooth the rectified signal. More
capacitance will increase the response time.
19
R_OSC
Oscillator Resistor
A resistor from this terminal to circuit ground determines the operating frequency
of the oscillator. The MC33794 is optimized for operation around 120 kHz.
24
CLK
Clock
This terminal provides a square wave output at the same frequency as the
internal oscillator. The edges of the square wave coincide with the peaks
(positive and negative) of the sine wave.
25
VDD_MON
VDD Monitor
This is connected through an internal voltage divider to VDD REG. It allows
reduction of the voltage so it will fall within the range of the ADC on the MCU.
26
VDD
VDD Capacitor
A capacitor is connected to this terminal to filter the internal analog regulated
supply. This supply is derived from VPWR through internal VDD REG.
27
VPWR
Positive Power Supply
12 V power applied to this terminal will be converted to the regulated voltages
needed to operate the part. It is also converted to 5.0 V (internal VCC REG) and
8.5 V (internal VDD REG) to power the MCU and external devices.
28
VCC
5.0 V Regulator Output
This output terminal requires a 47 F capacitor and internal VCC REG provides
a regulated 5.0 V for the MCU and for internal needs of the MC33794.
29
AGND
Analog Ground
This terminal is connected to the ground return of the analog circuitry. This
ground should be kept free of transient electrical noise like that from logic
switching. Its path to the electrical current return point should be kept separate
from the return for GND.
30
SHIELD
Shield Driver
This terminal connects to cable shields to cancel cable capacitance.
Table 1. SOICW-EP TERMINAL FUNCTION DESCRIPTION (continued)
Terminal
Name
Formal Name
Definition
相關PDF資料 |
PDF描述 |
|---|---|
| 225395-1 | CONN PLUG BNC RG 58 DUAL CRIMP |
| MCZ33793EFR2 | IC DSI SLAVE FOR R-SENSE 16-SOIC |
| CS4121EDWFR20G | IC TACH/SPEEDO DRIVER 20-SOIC |
| CS4121EDWFR20 | IC TACH/SPEEDO DRIVER 20-SOIC |
| CS4121EDWF20G | IC TACH/SPEEDO DRIVER 20-SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC33794EKR2 | 功能描述:近程傳感器 ODS 54LD RoHS:否 制造商:Vishay Semiconductors 感應方式:Optical 感應距離:1 mm to 200 mm 電源電壓:2.5 V to 3.6 V 安裝風格:SMD/SMT 輸出配置:Digital 最大工作溫度:+ 85 C 最小工作溫度:- 25 C 系列:VCNL3020 |
| MC33797BPEW | 功能描述:功率驅動器IC Four Channel Squib Dr RoHS:否 制造商:Micrel 產品:MOSFET Gate Drivers 類型:Low Cost High or Low Side MOSFET Driver 上升時間: 下降時間: 電源電壓-最大:30 V 電源電壓-最小:2.75 V 電源電流: 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| MC33797BPEWR2 | 功能描述:功率驅動器IC Four Channel Squib Dr RoHS:否 制造商:Micrel 產品:MOSFET Gate Drivers 類型:Low Cost High or Low Side MOSFET Driver 上升時間: 下降時間: 電源電壓-最大:30 V 電源電壓-最小:2.75 V 電源電流: 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| MC33813AE | 功能描述:功率驅動器IC 1 CYL SM ENG CONTROL IC RoHS:否 制造商:Micrel 產品:MOSFET Gate Drivers 類型:Low Cost High or Low Side MOSFET Driver 上升時間: 下降時間: 電源電壓-最大:30 V 電源電壓-最小:2.75 V 電源電流: 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| MC33813AER2 | 功能描述:功率驅動器IC 1 CYL SM ENG CONTROL IC RoHS:否 制造商:Micrel 產品:MOSFET Gate Drivers 類型:Low Cost High or Low Side MOSFET Driver 上升時間: 下降時間: 電源電壓-最大:30 V 電源電壓-最小:2.75 V 電源電流: 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。