參數資料
型號: MC33689DDWBR2
廠商: Freescale Semiconductor
文件頁數: 13/31頁
文件大小: 0K
描述: IC SYSTEM BASE W/LIN 32-SOIC
標準包裝: 1
應用: 自動鏡像控制
接口: SPI
電源電壓: 5.5 V ~ 18 V
封裝/外殼: 32-SOIC(0.295",7.50mm 寬)
供應商設備封裝: 32-SOIC
包裝: 剪切帶 (CT)
安裝類型: 表面貼裝
配用: KIT33689DWBEVB-ND - KIT FOR 33689 SBC WITH LIN
Analog Integrated Circuit Device Data
20
Freescale Semiconductor
33689
FUNCTIONAL DESCRIPTION
FUNCTIONAL PIN DESCRIPTION
RESET OUTPUT PIN (RST)
The RST pin is the 5.0 V regulator and Watchdog reset
output pin.
PWM INPUT CONTROL PIN (IN)
The IN pin is the external PWM control pin for the HS1 and
HS2 high-side switches.
SERIAL DATA CLOCK PIN (SCLK)
The SCLK pin is the SPI clock input pin. MISO data
changes on the negative transition of the SCLK. MOSI is
sampled on the positive edge of the SCLK.
MASTER OUT SLAVE IN PIN (MOSI)
The MOSI pin receives SPI data from the MCU. This data
input is sampled on the positive edge of SCLK.
MASTER IN SLAVE OUT PIN (MISO)
The MISO pin sends data to an SPI-enabled MCU. Data
on this output pin changes on the negative edge of the SCLK.
When CS is HIGH, this pin enters the high-impedance state.
CHIP SELECT PIN (CS)
The CS pin is the chip select input pin for SPI use. When
this signal is high, SPI signals are ignored. Asserting this pin
LOW starts an SPI transaction. The transaction is completed
when this signal returns HIGH.
INTERRUPT OUTPUT PIN (INT)
The INT pin is used to report 33689 faults to the MCU.
Interrupt pulses are generated for:
Voltage regulator temperature pre-warning
HS1, HS2, or HS3 thermal shutdown
VS1 or VS2 overvoltage (20 V typical)
VS1 or VS2 undervoltage (6.0 V typical)
If an interrupt is generated, then when the next SPI read
operation is performed bit D7 in the SPI Register will be set
to logic [1] and bits D6:D0 will report the interrupt source.
In cases of wake-up from the Stop mode, INT is set LOW
in order to signal to the MCU that a wake-up event from the
L1, L2, or LIN bus pin has occurred.
RECEIVER OUTPUT PIN (RXD)
The RXD pin is the receiver output of the LIN interface and
reports the state of the bus voltage (RXD LOW when LIN bus
is dominant, RXD HIGH when LIN bus is recessive).
TRANSMITTER INPUT PIN (TXD)
The TXD pin is the transmitter input of the LIN interface
and controls the state of the bus output (dominant when TXD
is LOW, recessive when TXD is HIGH).
GROUND PINS (GND, TGND, AND AGND)
The 33689 has three different types of ground pins.
The GND pin is the electrical ground pin for the device.
The AGND is the analog ground pin for the voltage
regulator and current sense operational amplifier.
The four TGND pins are the thermal ground pins for the
device.
Important The GND, the AGND, and the four TGND pins
must be connected together to a ground external to the
33689.
相關PDF資料
PDF描述
MC33742EPR2 IC SYSTEM BASE W/CAN 48-QFN
MC33780EG IC DBUS MASTER DUAL DIFF 16-SOIC
MC33790DW IC DSI 2-CHAN INTERFACE 16-SOIC
MC33794EKR2 IC SENSOR ELECTRIC FIELD 54SOICW
MC33889BDW IC SYSTEM BASE W/CAN 28-SOIC
相關代理商/技術參數
參數描述
MC33689DPEW 制造商:Freescale Semiconductor 功能描述:SYSTEM BASIS CHIP W/LIN 制造商:Freescale Semiconductor 功能描述:SYSTEM BASIS CHIP W/LIN - Bulk 制造商:Freescale Semiconductor 功能描述:IC SYSTEM BASIS W/LIN 32SOIC
MC33689DPEWR2 制造商:Freescale Semiconductor 功能描述:SYSTEM BASIS CHIP W/LIN 制造商:Freescale Semiconductor 功能描述:SYSTEM BASIS CHIP W/LIN - Tape and Reel 制造商:Freescale Semiconductor 功能描述:IC SYSTEM BASIS W/LIN 32SOIC
MC33689DWB 功能描述:CAN 接口集成電路 SBCLIN RoHS:否 制造商:Texas Instruments 類型:Transceivers 工作電源電壓:5 V 電源電流: 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:SOIC-8 封裝:Tube
MC33689DWBR2 功能描述:CAN 接口集成電路 SBCLIN RoHS:否 制造商:Texas Instruments 類型:Transceivers 工作電源電壓:5 V 電源電流: 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:SOIC-8 封裝:Tube
MC33690DWE 功能描述:數字信號處理器和控制器 - DSP, DSC STAND ALONE TAG READER RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT