參數資料
型號： MC33389DDW
廠商： Freescale Semiconductor
文件頁數： 16/49頁
文件大?。?/td> 0K
描述： IC SYSTEM BASE W/CAN 28-SOIC
標準包裝： 1
控制器類型： 系統基礎芯片
接口： CAN
電源電壓： 5.5 V ~ 18 V
電流 - 電源： 45mA
工作溫度： -40°C ~ 125°C
安裝類型： 表面貼裝
封裝/外殼： 28-SOIC（0.295"，7.50mm 寬）
供應商設備封裝： 28-SOIC W
包裝： 管件
Analog Integrated Circuit Device Data
Freescale Semiconductor
23
33389
FUNCTIONAL DEVICE OPERATION
OPERATIONAL MODES
SBC Normal Mode
In this mode, V1 and V2 are active, V3 can be set active
or passive via the SPI. Therefore, the whole ECU can be
operated. Normal mode is entered by a SWCR configuration
in the Normal Request mode.
SBC Stand-by Mode
In this mode V1 is active and V2 is passive. V3 can be
either permanently active or permanently passive. This is a
low power mode with V1 active in order to have a fast
reaction time in case of any wake-up.
For Stand-by mode, the S Bus Circuit (SBC) monitors the
software. It means the microcontroller runs, is monitored, and
must serve as a watchdog trigger.
S Bus Circuit Sleep Mode
This is a low power consumption mode. V1 and V2 are
disabled. V3 can be permanently disabled or cyclically active.
Emergency Mode
In case the microcontroller detects the ECU or the system
is no longer under control, it may decide to switch the SBC to
the Emergency mode. V1, V2, and V3 become passive and
wake-ups are not detected. The only way to leave this mode
is to disconnect the ECU from the battery voltage (BatFail
detection).
Table 9. Normal Request: V1 Active and V2/V3 Passive
Entering Normal Request
Leaving Normal Request
SBC Reset Just Released
When First Receiving the SW
Timing Word, SBC goes to
Normal
—
If Time-out Without Receiving
SPI Commands (75ms), SBC
goes to Seep
Table 10. SBC Normal Mode: V1/V2 Active
While V3 is Active or Passive
Entering Normal Mode
Leaving Normal Mode
By SPI command
By SPI command, going to any
other mode
After SWCR register
configuration in
Normal Request mode
Watchdog time-out, going to
Normal Request after activat-
ing Reset
—
V1 undervoltage detection,
going to Normal Request mode
after activating Reset
Table 11. Stand-by: V1 Active, V2 Passive, V3 Active
or Passive, Watchdog is Active
Entering Stand-by
Leaving Stand-by
—
If SW Timeout Going to Normal
Request After
Microcontroller Reset
By SPI Command
By SPI Command Going to any
Other Mode
—
V1 Under Voltage Detection,
Going to Normal Request Mode
After Activating Reset
—
External Activation of the RST
Pin
Table 12. SBC Sleep Mode: V1/V2 are Passive,
V3 is Passive or Cyclic
Entering Sleep Mode
Leaving Sleep Mode
If SW Timing Not Configured
75 ms After Entering
Normal Request Mode
CAN Wake-Up, Going to
Normal Request
By SPI Command
If a Wake-Up is Detected with
Cyclic Sense
For 33389ADW Only: If V1 is
Below V1 Reset for More Than
100 ms
If a Wake-Up is Detected with
Wake-Up Not Connected to V3
(permanent sense)
—
Forced Wake-Up (See Forced
Wake-Up Section)
—
SPI Wake-Up (See Wake-Up
by SPI Section)
Table 13. SBC Emergency Mode: V1:V3 are Passive
Entering Emergency Mode
Leaving Emergency Mode
By SPI Command
SBC BatFail Detection (Discon-
nection of the Battery Voltage)
Table 11. Stand-by: V1 Active, V2 Passive, V3 Active
or Passive, Watchdog is Active
Entering Stand-by
Leaving Stand-by
相關PDF資料
PDF描述
MC33394DH IC POWER SUPPLY MULT-OUT 44-HSOP
MC33560DW OC PWR MGMT READERS/CPLR 24-SOIC
MC33689DDWBR2 IC SYSTEM BASE W/LIN 32-SOIC
MC33742EPR2 IC SYSTEM BASE W/CAN 48-QFN
MC33780EG IC DBUS MASTER DUAL DIFF 16-SOIC
相關代理商/技術參數
參數描述
MC33389DDWR2 功能描述:網絡控制器與處理器 IC SBC SOW28 RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
MC33390D 功能描述:IC TRANSCEIVER SER LINK 8-SOIC RoHS:否 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:1,000 系列:- 類型:收發器 驅動器/接收器數:2/2 規程:RS232 電源電壓:3 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:16-SOIC 包裝:帶卷 (TR)
MC33390DR2 功能描述:IC TRANSCEIVER SER LINK 8-SOIC RoHS:否 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:1,000 系列:- 類型:收發器 驅動器/接收器數:2/2 規程:RS232 電源電壓:3 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:16-SOIC 包裝:帶卷 (TR)
MC33390EF 制造商:Freescale Semiconductor 功能描述:
MC33394DH 功能描述:IC POWER SUPPLY MULT-OUT 44-HSOP RoHS:否 類別:集成電路 (IC) >> 接口 - 專用 系列:- 標準包裝:3,000 系列:- 應用:PDA，便攜式音頻/視頻，智能電話 接口:I²C，2 線串口 電源電壓:1.65 V ~ 3.6 V 封裝/外殼:24-WQFN 裸露焊盤 供應商設備封裝:24-QFN 裸露焊盤（4x4） 包裝:帶卷 (TR) 安裝類型:表面貼裝 產品目錄頁面:1015 (CN2011-ZH PDF) 其它名稱:296-25223-2
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*