參數資料
型號： MC33388D
廠商： MOTOROLA INC
元件分類： 網絡接口
英文描述： Fault Tolerant CAN Interface
中文描述： DATACOM, INTERFACE CIRCUIT, PDSO14
封裝： PLASTIC, SO-14
文件頁數： 27/28頁
文件大?。?/td> 454K
代理商： MC33388D
MC33388
Electromagnetic Compatibility
MC33388
MOTOROLA
13
Introduction
The device is designed for optimized noise emission (EMI)
and high susceptibility performances (EMC). The source for
both disturbance and susceptibility is primarily coming form the
bus line wires. They are by far the longest connections
compared to the printed circuit board of the application
receiving the MC333388, the microcontroller and the other
components.
EMI Noise
In order to minimize the HF noise generated by the
complete application, the MC33388 minimizes the common
mode voltage and current glitches occurring at each bus
transition : from dominant to recessive and from recessive to
dominant. This is achieves by excellent matching in signal
transition between CANL and CANH. The common mode
voltage and current glitches are defined as follow :
CmV = (Vcanh+Vcanl)/2,
CmI = (Icanh+Icanl)/2.
The device is optimized for dual wires operations. Under a
fault condition, for instance one CAN bus connection shorted to
fixed voltage, e.g GND, the common mode will be considerably
degraded.
Figure below shows the typical signals for common mode
voltage measured at CANL and CANH pins.
Figure 5. Typical Common Mode Glitch
Measured at CANL CANH
Tx: 5V/div
Glitch
100mV/div
NERR: 5V/div
CAUTION : The common mode voltage characteristics are
dependant upon immediate device environment, such as bus
capacitor loading, bus wire length and type, etc... In addition, the
symmetry of the CANL and CANH bus lines is key parameter to
optimize common mode glitches. For instance un-symmetry
could result in different parasitic capacitors value between
CANL to GND and CANH to GND and will increase common
mode glitches and degrade overall system performances.
EMC Susceptibility Performances
The MC33388 is optimized for high immunity from external
field disturbances. The bus lines are by far the primary antenna
for external field coupling to the CANL, CANH, Rtl and Rth
connections. The device performances are characterized using
the Bulk Current Injection (BCI) test method, derivated from
specification ISO 11452-4.
Susceptibility evaluation with BCI :
The component is configured according to the electrical
schematic very close to the typical application schematic, figure
4. Main difference is that the microcontroller is replaced by an
external generator and analyzer connected to RX, TX and
NERR through optical link. A network composed of two nodes
equipped with MC33388, one in emitter and one in receiver is
evaluated. The disturbance is applied to both CANL and CANH
twisted pair bus line lines with appropriate coupling clamp.
During test sequences, received bits are compared to
transmit bits. When received bits are different from transmit bits
the device is considered as fail for the particular frequency.
Results
Figures 7 and 8 below describe the device susceptibility
performances in the frequency range of 1 to 400MHz with target
of injected current of 200mA and 316mA.
When the target current is reached and when no
susceptibility is observed, the next frequency point is analyzed,
until reaching the max frequency, 400Mhz. If a susceptibility is
observed for a particular frequency, the free point is marked.
Figure 7 below shows results with a target susceptibility level
of 316mA or 49dBmA with a 1KHz 80% modulation added to the
injected current. Figure 8 shows the susceptibility levels with a
target susceptibility level of 200mA or 46dBmA without
modulation added to the injected current.
Figure 6. Min. Susceptibility Level With Modulation
1.0
10
100
1000
20
30
40
60
10
FREQUENCY (MHz)
C
50
LIMIT OF TEST (49dB) (No Susceptibility)
NO SUSCEPTIBILITY AREA
Susceptibility Points
Figure 7. Min. Susceptibility Level Without Modulation
1.0
10
1000
20
30
40
50
46
60
10
FREQUENCY (MHz)
C
NO SUSCEPTIBILITY AREA
Susceptibility Points
LIMIT OF TEST (46dB) (No Susceptibility)
相關PDF資料
PDF描述
MC33388 Fault Tolerant CAN Interface
MC33501 1.0 V, Rail-to-Rail, Single Operational Amplifiers(1.0V,軌對軌,單運算放大器)
MC33503 1.0 V, Rail-to-Rail, Single Operational Amplifiers(1.0V,軌對軌,單運算放大器)
MC33566 Smart Voltage Regulator for Peripheral Card Applications(用于PCI/NIC卡應用的小型低壓差穩壓器)
MC33761 Ultra Low-Noise Low Dropout Voltage Regulator with 1.0 V ON/OFF Control(超低噪聲，帶1.0V開關控制的低壓差穩壓器)
相關代理商/技術參數
參數描述
MC33388DR2 功能描述:IC TOLERANT CAN INT FAULT 14SOIC RoHS:否 類別:集成電路 (IC) >> 接口 - 控制器 系列:- 標準包裝:4,900 系列:- 控制器類型:USB 2.0 控制器 接口:串行 電源電壓:3 V ~ 3.6 V 電流 - 電源:135mA 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:36-VFQFN 裸露焊盤 供應商設備封裝:36-QFN（6x6） 包裝:* 其它名稱:Q6396337A
MC33389CDH 功能描述:IC SYSTEM BASIS W/CAN 20-HSOP RoHS:是 類別:集成電路 (IC) >> 接口 - 控制器 系列:- 標準包裝:4,900 系列:- 控制器類型:USB 2.0 控制器 接口:串行 電源電壓:3 V ~ 3.6 V 電流 - 電源:135mA 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:36-VFQFN 裸露焊盤 供應商設備封裝:36-QFN（6x6） 包裝:* 其它名稱:Q6396337A
MC33389CDHR2 功能描述:IC SYSTEM BASE W/CAN 20-HSOP RoHS:是 類別:集成電路 (IC) >> 接口 - 控制器 系列:- 標準包裝:4,900 系列:- 控制器類型:USB 2.0 控制器 接口:串行 電源電壓:3 V ~ 3.6 V 電流 - 電源:135mA 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:36-VFQFN 裸露焊盤 供應商設備封裝:36-QFN（6x6） 包裝:* 其它名稱:Q6396337A
MC33389CDW 功能描述:網絡控制器與處理器 IC SYSTEM BASIC CHIPS RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
MC33389CDWR2 功能描述:網絡控制器與處理器 IC SYSTEM BASIC CHIPS RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*