參數資料
型號: MC33262DR2G
廠商: ON SEMICONDUCTOR
元件分類: 穩壓器
英文描述: Power Factor Controllers
中文描述: 0.5 A POWER FACTOR CONTROLLER, PDSO8
封裝: LEAD FREE, PLASTIC, SOIC-8
文件頁數: 7/19頁
文件大?。?/td> 399K
代理商: MC33262DR2G
MC34262, MC33262
http://onsemi.com
7
Operating Description
The MC34262, MC33262 contain many of the building
blocks and protection features that are employed in modern
high performance current mode power supply controllers.
There are, however, two areas where there is a major
difference when compared to popular devices such as the
UC3842 series. Referring to the block diagram in
Figure 19, note that a multiplier has been added to the
current sense loop and that this device does not contain an
oscillator. The reasons for these differences will become
apparent in the following discussion. A description of each
of the functional blocks is given below.
Figure 18. Active Power Factor Correction Preconverter
Rectifiers
PFC Preconverter
High
Frequency
Bypass
Capacitor
+
Converter
Bulk
Storage
Capacitor
+
Load
MC34362
AC
Line
Error Amplifier
An Error Amplifier with access to the inverting input and
output is provided. The amplifier is a transconductance
type, meaning that it has high output impedance with
controlled voltagetocurrent gain. The amplifier features
a typical gm of 100 mhos (Figure 5). The noninverting
input is internally biased at 2.5 V
±
2.0% and is not pinned
out. The output voltage of the power factor converter is
typically divided down and monitored by the inverting
input. The maximum input bias current is 0.5 A, which
can cause an output voltage error that is equal to the product
of the input bias current and the value of the upper divider
resistor R
2
. The Error Amp output is internally connected
to the Multiplier and is pinned out (Pin 2) for external loop
compensation. Typically, the bandwidth is set below 20 Hz,
so that the amplifier’s output voltage is relatively constant
over a given ac line cycle. In effect, the error amp monitors
the average output voltage of the converter over several
line cycles. The Error Amp output stage was designed to
have a relatively constant transconductance over
temperature. This allows the designer to define the
compensated bandwidth over the intended operating
temperature range. The output stage can sink and source
10 A of current and is capable of swinging from 1.7 V to
6.4 V, assuring that the Multiplier can be driven over its
entire dynamic range.
A key feature to using a transconductance type amplifier,
is that the input is allowed to move independently with
respect to the output, since the compensation capacitor is
connected to ground. This allows dual usage of of the
Voltage Feedback Input pin by the Error Amplifier and by
the Overvoltage Comparator.
Overvoltage Comparator
An Overvoltage Comparator is incorporated to eliminate
the possibility of runaway output voltage. This condition
can occur during initial startup, sudden load removal, or
during output arcing and is the result of the low bandwidth
that must be used in the Error Amplifier control loop. The
Overvoltage Comparator monitors the peak output voltage
of the converter, and when exceeded, immediately
terminates MOSFET switching. The comparator threshold
is internally set to 1.08 V
ref
. In order to prevent false
tripping during normal operation, the value of the output
filter capacitor C
3
must be large enough to keep the
peaktopeak ripple less than 16% of the average dc
output. The Overvoltage Comparator input to Drive Output
turnoff propagation delay is typically 400 ns. A
comparison of startup overshoot without and with the
Overvoltage Comparator circuit is shown in Figure 23.
Multiplier
A single quadrant, two input multiplier is the critical
element that enables this device to control power factor.
The ac full wave rectified haversines are monitored at Pin 3
with respect to ground while the Error Amp output at Pin 2
is monitored with respect to the Voltage Feedback Input
threshold. The Multiplier is designed to have an extremely
linear transfer curve over a wide dynamic range, 0 V to
3.2 V for Pin 3, and 2.0 V to 3.75 V for Pin 2, Figure 1. The
Multiplier output controls the Current Sense Comparator
threshold as the ac voltage traverses sinusoidally from zero
to peak line, Figure 18. This has the effect of forcing the
MOSFET ontime to track the input line voltage, resulting
in a fixed Drive Output ontime, thus making the
preconverter load appear to be resistive to the ac line. An
approximation of the Current Sense Comparator threshold
can be calculated from the following equation. This
equation is accurate only under the given test condition
stated in the electrical table.
V
CS
, Pin 4 Threshold
0.65 (V
Pin 2
V
th(M)
) V
Pin 3
相關PDF資料
PDF描述
MC33262PG Power Factor Controllers
MC33274A Single Supply, High Slew Rate, Low Input Offset Voltage Operational Amplifiers(單電源,高壓擺率,低輸入偏置電壓運放)
MC33363A CABLE ASSEMBLY; SMA MALE TO N FEMALE BULKHEAD; 50 OHM, PE-SR047FL (.047" RE-SHAPABLE); 60" CABLE LENGTH;
MC33363ADW Isolated Flyback Switching Regulator with 9V Output
MC33363AP Isolated Flyback Switching Regulator with 9V Output
相關代理商/技術參數
參數描述
MC33262P 功能描述:功率因數校正 IC Critical Mode PFC RoHS:否 制造商:Fairchild Semiconductor 開關頻率:300 KHz 最大功率耗散: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Reel
MC33262PG 功能描述:功率因數校正 IC Critical Mode PFC w/OVP RoHS:否 制造商:Fairchild Semiconductor 開關頻率:300 KHz 最大功率耗散: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Reel
MC33263 制造商:SPC Multicomp 功能描述:HEATSINK TO220 14/W 制造商:SPC Multicomp 功能描述:HEATSINK TO220 14C/W 制造商:SPC Multicomp 功能描述:HEAT SINK; Packages Cooled:TO-220; Thermal Resistance:13.4C/W; External Height - Imperial:1"; External Height - Metric:25.4mm; External Width - Imperial:1.374"; External Width - Metric:34.9mm; External Length - Imperial:0.5" ;RoHS Compliant: Yes
MC33263NW-30R2 制造商:Rochester Electronics LLC 功能描述:- Bulk
MC33263NW-38R2 制造商:Rochester Electronics LLC 功能描述:- Bulk