參數資料
型號: MC33153D
廠商: MOTOROLA INC
元件分類: 外設及接口
英文描述: Tag-it(TM) HF-I Standard Transponder Inlays Large Rectangle 0-RFIDN -25 to 70
中文描述: 2 A BUF OR INV BASED PRPHL DRVR, PDSO8
封裝: PLASTIC, SO-8
文件頁數: 9/12頁
文件大小: 189K
代理商: MC33153D
MC33153
9
MOTOROLA ANALOG IC DEVICE DATA
When the lower device is turned on, clearing the upper
diode, the turn–on dv/dt of the lower device appears across
the collector emitter of the upper device. To eliminate
shoot–through currents, it is necessary to provide a low sink
impedance to the device that is in the off–state. In most
applications the turn–off resistor can be made small enough
to hold off the device that is under commutation without
causing excessively fast turn–off speeds.
Figure 30. Using a Single Gate Resistor
Output
VCC
VEE
5
VEE
VEE
3
Rg
IGBT
Figure 31. Using Separate Resistors
for Turn–On and Turn–Off
Output
VCC
VEE
5
VEE
VEE
3
Ron
IGBT
Roff
Doff
A negative bias voltage can be used to drive the IGBT into
the off–state. This is a practice carried over from bipolar
Darlington drives and is generally not required for IGBTs.
However, a negative bias will reduce the possibility of
shoot–through. The MC33153 has separate pins for VEE and
Kelvin Ground. This permits operation using a +15/–5.0 V
supply.
INTERFACING WITH OPTOISOLATORS
Isolated Input
The MC33153 may be used with an optically isolated
input. The optoisolator can be used to provide level shifting,
and if desired, isolation from ac line voltages. An optoisolator
with a very high dv/dt capability should be used, such as the
Hewlett Packard HCPL4053. The IGBT gate turn–on resistor
should be set large enough to ensure that the opto’s dv/dt
capability is not exceeded. Like most optoisolators, the
HCPL4053 has an active low open–collector output. Thus,
when the LED is on, the output will be low. The MC33153 has
an inverting input pin to interface directly with an optoisolator
using a pull up resistor. The input may also be interfaced
directly to 5.0 V CMOS logic or a microcontroller.
Optoisolator Output Fault
The MC33153 has an active high fault output. The fault
output may be easily interfaced to an optoisolator. While it is
important that all faults are properly reported, it is equally
important that no false signals are propagated. Again, a high
dv/dt optoisolator should be used.
The LED drive provides a resistor programmable current
of 10 to 20 mA when on, and provides a low impedance path
when off. An active high output, resistor, and small signal
diode provide an excellent LED driver. This circuit is shown in
Figure 32.
Figure 32. Output Fault Optoisolator
Short Circuit
Latch Output
7
VEE
VCC
VEE
Q
UNDERVOLTAGE LOCKOUT
It is desirable to protect an IGBT from insufficient gate
voltage. IGBTs require 15 V on the gate to achieve the rated
on–voltage. At gate voltages below 13 V, the on–voltage
increases dramatically, especially at higher currents. At very
low gate voltages, below 10 V, the IGBT may operate in the
linear region and quickly overheat. Many PWM motor drives
use a bootstrap supply for the upper gate drive. The UVLO
provides protection for the IGBT in case the bootstrap
capacitor discharges.
The MC33153 will typically start up at about 12 V. The
UVLO circuit has about 1.0 V of hysteresis and will disable
the output if the supply voltage falls below about 11 V.
相關PDF資料
PDF描述
MC33153P Tag-it(TM) HF-I Plus Transponder Inlays Miniature Rectangle 0-RFIDN -25 to 70
MC33154 Tag-it(TM) HF-I Standard Transponder Inlays Miniature Rectangle 0-RFIDN -25 to 70
MC33154D Tag-it(TM) HF-I Pro Transponder Inlays Miniature Rectangle 0-RFIDN -25 to 70
MC33154P Tag-it(TM) HF-I Plus Transponder Inlays Square 0-RFIDN -25 to 70
MC33160DW Tag-it(TM) HF-I Pro Transponder Inlays Large Square 0-RFIDN -25 to 70
相關代理商/技術參數
參數描述
MC33153DG 功能描述:馬達/運動/點火控制器和驅動器 1A Source/2A Sink RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
MC33153DR2 功能描述:馬達/運動/點火控制器和驅動器 1A Source/2A Sink RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
MC33153DR2G 功能描述:馬達/運動/點火控制器和驅動器 1A Source/2A Sink RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
MC33153P 功能描述:馬達/運動/點火控制器和驅動器 1A Source/2A Sink RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
MC33153PG 功能描述:馬達/運動/點火控制器和驅動器 1A Source/2A Sink RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube