- 您現在的位置：買賣IC網 > PDF目錄385566 > MC33025DWR2 (ON SEMICONDUCTOR) High Speed Double−Ended PWM Controller PDF資料下載
參數資料
| 型號： | MC33025DWR2 |
| 廠商： | ON SEMICONDUCTOR |
| 元件分類： | 穩壓器 |
| 英文描述： | High Speed Double−Ended PWM Controller |
| 中文描述： | 2 A SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO16 |
| 封裝： | SOIC-16 |
| 文件頁數： | 9/20頁 |
| 文件大?。?/td> | 482K |
| 代理商： | MC33025DWR2 |
MC34025, MC33025
http://onsemi.com
9
If the voltage at this pin exceeds 1.4 V, the second
comparator is activated. This comparator sets a latch which,
in turn, causes the SoftStart capacitor to be discharged. In
this way a “hiccup” mode of recovery is possible in the case
of output short circuits. If a current limit resistor is used in
series with the output devices, the peak current at which the
controller will enter a “hiccup” mode is given by:
Ishutdown
1.4 V
RSense
Undervoltage Lockout
There are two undervoltage lockout circuits within the IC.
The first senses V
CC
and the second V
ref
. During powerup,
V
CC
must exceed 9.2 V and V
ref
must exceed 4.2 V before
the outputs can be enabled and the SoftStart latch released.
If V
CC
falls below 8.4 V or V
ref
falls below 3.6 V, the outputs
are disabled and the SoftStart latch is activated. When the
UVLO is active, the part is in a low current standby mode
allowing the IC to have an offline bootstrap startup circuit.
Typical startup current is 500 A.
Output
The MC34025 has two high current totem pole outputs
specifically designed for direct drive of power MOSFETs.
They are capable of up to
±
2.0 A peak drive current with a
typical rise and fall time of 30 ns driving a 1.0 nF load.
Separate pins for V
C
and Power Ground are provided.
With proper implementation, a significant reduction of
switching transient noise imposed on the control circuitry is
possible. The separate V
C
supply input also allows the
designer added flexibility in tailoring the drive voltage
independent of V
CC
.
Reference
A 5.1 V bandgap reference is pinned out and is trimmed
to an initial accuracy of
±
1.0% at 25
°
C. This reference has
short circuit protection and can source in excess of 10 mA
for powering additional control system circuitry.
Design Considerations
Do not attempt to construct the converter on
wirewrap or plugin prototype boards.
With high
frequency, high power, switching power supplies it is
imperative to have separate current loops for the signal paths
and for the power paths. The printed circuit layout should
contain a ground plane with low current signal and high
current switch and output grounds returning on separate
paths back to the input filter capacitor. All bypass capacitors
and snubbers should be connected as close as possible to the
specific part in question. The PC board lead lengths must be
less than 0.5 inches for effective bypassing or snubbing.
Instabilities
In current mode control, an instability can be encountered
at any given duty cycle. The instability is caused by the
current feedback loop. It has been shown that the instability
is caused by a double pole at half the switching frequency.
If an external ramp (S
e
) is added to the ontime ramp (S
n
)
of the currentsense waveform, stability can be achieved
(see Figure 21).
One must be careful not to add too much ramp
compensation. If too much is added, the system will start to
perform like a voltage mode regulator. All benefits of
current mode control will be lost. Figures 29A and 29B show
examples of two different ways in which external ramp
compensation can be implemented.
1.25 V
+
+
Ramp Input
Current Signal
S
n
Ramp Compensation
S
e
Figure 21. Ramp Compensation
A simple equation can be used to calculate the amount of
external ramp necessary to add that will achieve stability in
the current loop. For the following equations, the calculated
values for the application circuit in Figure 37 are also shown.
Se
VO
L
NS
NP
(RS)Ai
where:
= DC output voltage
= number of power transformer primary
=
or secondary turns
= gain of the current sense network
=
(see Figures 26, 27 and 28)
= output inductor
= current sense resistance
V
O
N
P
, N
S
A
i
L
R
S
0.115 V
μ
s
For the application circuit: Se
5
1.8
μ
4
相關PDF資料 |
PDF描述 |
|---|---|
| MC33025DWR2G | High Speed Double−Ended PWM Controller |
| MC33025PG | High Speed Double−Ended PWM Controller |
| MC3302 | Single Supply Quad Comparators(四電壓比較器) |
| MC3303 | Single Supply Quad Operational Amplifiers(單電源四運放) |
| MC3403 | Quadruple Low Power Operational Amplifiers(四路低功率通用運放) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC33025DWR2G | 功能描述:電流型 PWM 控制器 Dual Output Voltage or Current Mode PWM RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
| MC33025P | 功能描述:電流型 PWM 控制器 Dual Output Voltage RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
| MC33025PG | 功能描述:電流型 PWM 控制器 Dual Output Voltage or Current Mode PWM RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
| MC33029 | 制造商:SPC Multicomp 功能描述:FAN POWER CORD 制造商:SPC Multicomp 功能描述:FAN POWER CORD; For Use With:Axial Fans; Voltage Rating:300V; Fan Side Connector:45 Angle Plug; Cable Length:120"; Accessory Type:Fan Power Cord; Equipment Side Connector:Blunt Cut Wire Leads; Supply Voltage:300V ;RoHS Compliant: Yes |
| MC3302-BI/P | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:13-Bit Differential Input, Low Power A/D Converter with SPI Serial Interface |
發布緊急采購，3分鐘左右您將得到回復。