參數資料
型號： MC1GH128NACA-2SA00
廠商： SAMSUNG SEMICONDUCTOR CO. LTD.
英文描述： SAMSUNG MultiMediaCard
中文描述： 三星多媒體
文件頁數： 38/102頁
文件大小： 1384K
代理商： MC1GH128NACA-2SA00
MultiMediaCard
TM
38
Sep.22.2005
Revision 0.3
6. MultiMediaCard Protocol Description
All communication between host and card is controlled by the host (master). The host sends commands of two types:
broadcast and addressed (point-to-point) commands.
Broadcast commands : Broadcast commands are intended for all cards in a MultiMediaCard system
1
. Some of these
commands require a response.
Addressed (point-to-point) commands : The addressed commands are sent to the addressed card and cause a
response from this card.
A general overview of the command flow is shown in Figure 6-1 for the card identification mode and in Figure 6-2 for the
data transfer mode. The commands are listed in the command tables (Table 6-9 - Table 6-17). The dependencies between
current state, received command and following state are listed in Table 6-18. In the following sections, the different card
operation modes are described first. Thereafter, the restrictions for controlling the clock signal are defined. All MultiMedi-
aCard commands together with the corresponding responses, state transitions, error conditions and timings are presented
in the succeeding sections.
Three operation modes are defined for the MultiMediaCard system (hosts and cards):
Card identification mode
The host will be in card identification mode after reset, while it is looking for a card on the bus. The card will be in this
mode after reset, until the SET_RCA command (CMD3) is received.
Interrupt mode
Host and card enter and exit interrupt mode simultaneously. In interrupt mode there is no data transfer. The only mes
sage allowed is an interrupt service request from the card or the host.
Data transfer mode
The card will enter data transfer mode once an RCA is assigned to it. The host will enter data transfer mode after iden
tifying the card on the bus.
The following table shows the dependencies between bus modes, operation modes and card states. Each state in the
MultiMediaCard state diagram (see Figure 6-1 and Figure 6-2) is associated with one bus mode and one operation mode:
1.Broadcast commands are kept for backwards compatibility to previous MultiMediaCard systems, where more than one
card was allowed on the bus.
Card state
Operation mode
Bus mode
Inactive State
Inactive
Open-drain
Idle State
Card identification mode
Ready State
Identification State
Stand-by State
Data transfer mode
Push-pull
Transfer State
Bus-Test State
Sending-data State
Receive-data State
Programming State
Disconnect State
Wait-IRQ State
Interrupt mode
Open-drain
相關PDF資料
PDF描述
MC1GH256DACA-2SA00 SAMSUNG MultiMediaCard
MC2GH01GDMCA-2SA00 SAMSUNG MultiMediaCard
MC2GH256NMCA-2SA00 SAMSUNG MultiMediaCard
MC2GH512DMCA-2SA00 SAMSUNG MultiMediaCard
MC2GH512NMCA-2SA00 SAMSUNG MultiMediaCard
相關代理商/技術參數
參數描述
MC1GH256DACA-2SA00 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:SAMSUNG MultiMediaCard
MC1GU016HACA 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:MultiMediaCard Specification
MC1GU016HACA-0QC00 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:MultiMediaCard Specification
MC1GU016HACB-0QC00 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:MultiMediaCard Specification
MC1GU016HACC-0QC00 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:MultiMediaCard Specification
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*