參數資料
型號: MC145572AAC
廠商: Freescale Semiconductor
文件頁數: 11/52頁
文件大小: 0K
描述: IC TRANSCEIVER ISDN 44-LQFP
標準包裝: 160
類型: 收發器
規程: RS232
電源電壓: 5V
安裝類型: 表面貼裝
封裝/外殼: 44-LQFP
供應商設備封裝: 44-LQFP(10x10)
包裝: 托盤
MC145572EVK
20
2.5.1
Setting Up a Bit Error Rate Test
Bit error rate testing with two different testers has been performed. The Hewlett Packard 1645A Data Error
Analyzer and The Telecommunications Techniques Corporation FIREBERD 6000 with Lab Interface
Adapter have successfully been connected to the MC145572EVK. Any bit error test that accepts TTL level
signals and external data clocks up to 2.56 MHz at TTL levels may be used. The clock interface supports
synchronous clocked data through the use of gated clocks running at IDL rates of 512 kHz, 2.048 MHz,
or 2.56 MHz, as determined by register BR7(b2) and OR7(b4) of the U-Interface Transceiver.
CAUTION
The MC145572EVK does not support EIA-232, RS-422, 50W, or RS-485 interfaces to bit
error rate testers.
To demonstrate the connection of the MC145572EVK U-Interface Transceiver Evaluation Kit to a bit error
rate tester, detailed instructions for one test set-up follows.
EXAMPLE: Executing a 2B+D Loop-Back to the U-Interface at the LT End.
This example shows how to connect a bit error rate tester to the MC145572EVK. Refer to Figure 2-7 for
connection details.
The data ow for this example occurs as follows: data is input to the board by the BERT box on NTRXDATA
at the NT1. This data is then input to the MC145572 where it is framed, coded, and transmitted over the
U-Interface to the LT MC145572, and looped-back internal to the LT MC145572. The data is then
transmitted back to the NT MC145572 over the U-Interface, decoded, deframed, and output from the NT
MC145572 on NTTXDATA to the BERT box where it is compared to the data originally transmitted.
1. Make the following connections to the Bit Error Rate Tester as shown in Figure 2-7.
a. Connect NTTXDATA (BNC J20, Dout pin of the NT U-Interface Transceiver) to the Receive
Data Input of the BERT box.
b. Connect NTRXDATA (BNC JP18, Din pin of the NT U-Interface Transceiver) to the Transmit
Data Output of the BERT box.
c. Connect NTCLK (BNC J21, gated clock output for the B1+B2+D time slot) to the External
Transmit and External Receive Clock inputs of the BERT box.
2. Verify that the DIP switches are set as in Figure 1-3 (valid for above-mentioned BERT boxes).
3. Congure the bit error rate tester to transmit data on the rising edge of the data clock and receive
data on the falling edge of the data clock.
4. Using an ASCII terminal connected to J16, activate the MC145572EVK using the activation menu
item J. Activate both U chips, 2B+D loop back to U-Interface at LT end, disable S/T chip.
5. Begin bit error rate testing when status LEDs indicate loop is successfully activated.
F
re
e
sc
a
le
S
e
m
ic
o
n
d
u
c
to
r,
I
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
n
c
..
.
相關PDF資料
PDF描述
MC14LC5480ENR2 IC CODEC-FILTER PCM 5V 20-SSOP
MC14LC5540DW IC CODEC ADPCM 28-SOIC W
MC33199DR2 IC DRVR SER INK ISO9141 14-SOIC
MC33215BE IC SPEAKERPHONE CIRCUIT 42-SDIP
MC33990DR2 IC TRANSCEIVER J-1850 BUS 8-SOIC
相關代理商/技術參數
參數描述
MC145572ACR2 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:Freescale Semiconductor 功能描述:
MC145572AEI 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:Freescale Semiconductor 功能描述:
MC145572AFN 功能描述:IC TRANSCEIVER ISDN 44-PLCC RoHS:否 類別:集成電路 (IC) >> 接口 - 驅動器,接收器,收發器 系列:- 標準包裝:1,000 系列:- 類型:收發器 驅動器/接收器數:2/2 規程:RS232 電源電壓:3 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:16-SOIC(0.295",7.50mm 寬) 供應商設備封裝:16-SOIC 包裝:帶卷 (TR)
MC145572APB 功能描述:IC ISDN INTERFACE TXCVER 44-LQFP RoHS:否 類別:集成電路 (IC) >> 接口 - 驅動器,接收器,收發器 系列:- 標準包裝:1,000 系列:- 類型:收發器 驅動器/接收器數:2/2 規程:RS232 電源電壓:3 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:16-SOIC(0.295",7.50mm 寬) 供應商設備封裝:16-SOIC 包裝:帶卷 (TR)
MC145572APBR2 制造商:Rochester Electronics LLC 功能描述:- Bulk