- 您現在的位置：買賣IC網 > PDF目錄371012 > MC14467-1 (Motorola, Inc.) IonizationSmoke Detector IC(電離煙霧檢測器) PDF資料下載
參數資料
| 型號： | MC14467-1 |
| 廠商： | Motorola, Inc. |
| 英文描述： | IonizationSmoke Detector IC(電離煙霧檢測器) |
| 中文描述： | IonizationSmoke檢測器IC（電離煙霧檢測器） |
| 文件頁數： | 5/8頁 |
| 文件大?。?/td> | 155K |
| 代理商： | MC14467-1 |
5
Motorola Sensor Device Data
DEVICE OPERATION
TIMING
The internal oscillator of the MC14467–1 operates with a
period of 1.67 seconds during no–smoke conditions. Each
1.67 seconds, internal power is applied to the entire IC and a
check is made for smoke, except during LED pulse, Low Bat-
tery Alarm Chirp, or Horn Modulation (in smoke). Every 24
clock cycles a check is made for low battery by comparing
V
DD
to an internal zener voltage. Since very small currents
are used in the oscillator, the oscillator capacitor should be of
a low leakage type.
DETECT CIRCUITRY
If smoke is detected, the oscillator period becomes 40 ms
and the piezoelectric horn oscillator circuit is enabled. The
horn output is modulated 160 ms on, 80 ms off. During the off
time, smoke is again checked and will inhibit further horn out-
put if no smoke is sensed. During smoke conditions the low
battery alarm is inhibited, but the LED pulses at a 1.0 Hz rate.
An active guard is provided on both pins adjacent to the
detect input. The voltage at these pins will be within 100 mV
of the input signal. This will keep surface leakage currents to
a minimum and provide a method of measuring the input volt-
age without loading the ionization chamber. The active guard
op amp is not power strobed and thus gives constant protec-
tion from surface leakage currents. Pin 15 (the Detect input)
has internal diode protection against static damage.
SENSITIVITY/LOW BATTERY THRESHOLDS
Both the sensitivity threshold and the low battery voltage
levels are set internally by a common voltage divider (please
see Figure 1) connected between V
DD
and V
SS
. These volt-
ages can be altered by external resistors connected from
pins 3 or 13 to either V
DD
or V
SS
. There will be a slight inter-
action here due to the common voltage divider network. The
sensitivity threshold can also be set by adjusting the smoke
chamber ionization source.
TEST MODE
Since the internal op amps and comparators are power
strobed, adjustments for sensitivity or low battery level could
be difficult and/or time–consuming. By forcing Pin 12 to V
SS
,
the power strobing is bypassed and the outputs, Pins 1 and
4, constantly show smoke/no smoke and good battery/low
battery, respectively. Pin 1 = V
DD
for smoke and Pin 4 = V
DD
for low battery. In this mode and during the 10 ms power
strobe, chip current rises to approximately 50
μ
A.
LED PULSE
The 9–volt battery level is checked every 40 seconds dur-
ing the LED pulse. The battery is loaded via a 10 mA pulse
for 10 ms. If the LED is not used, it should be replaced with
an equivalent resistor such that the battery loading remains
at 10 mA.
HYSTERESIS
When smoke is detected, the resistor/divider network that
sets sensitivity is altered to increase sensitivity. This yields
approximately 100 mV of hysteresis and reduces false
triggering.
Figure 5. Typical Application as Ionization Smoke Detector
MC14467–1
1
16
2
3
4
5
6
7
8
15
14
13
12
11
10
9
330
8.2 M
9 V
+
0.1
μ
F
1.5 M
*
0.001*
μ
F
220 k
*
0.1
μ
F
1 M
1 M
TEST
*NOTE: Component values may change depending on type of piezoelectric horn used.
相關PDF資料 |
PDF描述 |
|---|---|
| MC14501BCL | Dual 4-Input NAND Gate, 2-Input NOR/OR Gate, 8-Input AND/NAND Gate |
| MC14501BD | Dual 4-Input NAND Gate, 2-Input NOR/OR Gate, 8-Input AND/NAND Gate |
| MC14501BCP | Dual 4-Input NAND Gate, 2-Input NOR/OR Gate, 8-Input AND/NAND Gate |
| MC14503BCP | Full Featured -48V Hot Swap Power Manager, Industrial Temp. 14-TSSOP -40 to 85 |
| MC14503 | Hex Non-Inverting 3-State Buffer |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC14467P1 | 功能描述:IC SMOKE DETECTOR 16-DIP RoHS:否 類別:集成電路 (IC) >> 接口 - 傳感器和探測器接口 系列:- 其它有關文件:Automotive Product Guide 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:74 系列:- 類型:觸控式傳感器 輸入類型:數字 輸出類型:數字 接口:JTAG，串行 電流 - 電源:100µA 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:20-TSSOP 包裝:管件 |
| MC14468P | 功能描述:IC SMOKE DETECT IONIZATN 16-DIP RoHS:否 類別:集成電路 (IC) >> 接口 - 傳感器和探測器接口 系列:- 其它有關文件:Automotive Product Guide 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:74 系列:- 類型:觸控式傳感器 輸入類型:數字 輸出類型:數字 接口:JTAG，串行 電流 - 電源:100µA 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:20-TSSOP 包裝:管件 |
| MC14489BDW | 功能描述:IC DRIVER LED/LAMP 5CH 20-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 顯示器驅動器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 顯示器類型:真空熒光 (VF) 配置:5 x 7（矩陣） 接口:串行 數字或字符:- 電流 - 電源:3.5mA 電源電壓:2.7 V ~ 3.6 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:16-SSOP（0.154"，3.90mm 寬） 供應商設備封裝:16-QSOP 包裝:帶卷 (TR) |
| MC14489BDWE | 功能描述:LED顯示驅動器 5 CHANNEL LED DRIVER RoHS:否 制造商:Micrel 數位數量:5 片段數量: 安裝風格:SMD/SMT 封裝 / 箱體:PLCC-44 工作電源電壓:4.75 V to 11 V 最大電源電流:10 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝:Tube |
| MC14489BDWER2 | 功能描述:LED顯示驅動器 5 CHANNEL LED DRIVER RoHS:否 制造商:Micrel 數位數量:5 片段數量: 安裝風格:SMD/SMT 封裝 / 箱體:PLCC-44 工作電源電壓:4.75 V to 11 V 最大電源電流:10 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。