- 您現在的位置：買賣IC網 > PDF目錄384724 > MC10SX1130DR2 (ON SEMICONDUCTOR) LED Driver PDF資料下載
參數資料
| 型號： | MC10SX1130DR2 |
| 廠商： | ON SEMICONDUCTOR |
| 元件分類： | 顯示驅動器 |
| 英文描述： | LED Driver |
| 中文描述： | LED DISPLAY DRIVER, PDSO16 |
| 封裝： | SOIC-16 |
| 文件頁數： | 2/9頁 |
| 文件大?。?/td> | 156K |
| 代理商： | MC10SX1130DR2 |
MC10SX1130
http://onsemi.com
2
15
16
14
13
12
11
10
2
1
3
4
5
6
7
V
EE
9
8
Stretch V
EE
I
OUT
RSET
I
OUT
V
CC
V
EE
V
EE
V
CC
V
BB
D
IN
D
IN
RTCO
1
RTCO
2
V
EE
Figure 1. Pinout: SOIC
16
(Top View)
PULSE WIDTH
ADJUST CIRCUIT
BIAS
CONTROL
RSET
RTCO
1
RTCO
2
I
OUT
I
OUT
Stretch
V
BB
D
IN
D
IN
ECL
BUFFER
Figure 2. Block Diagram
Table 1. PIN FUNCTION TABLE
Pin
Function
D
IN
Differential data inputs.
I
OUT
Differential open collector outputs.
STRETCH
Control input to select the amount of duty cycle pre-distortion. When the pin is left open, no pre-distortion is
introduced. If the pin is connected to V
CC
, the output LOW state current pulse width is increased by 155 ps. When it
is connected to V
EE
, the current pulse width is increased by 310 ps.
RSET
Resistor to set LED drive current. This resistor sets the tail current of the output current switch and should be con-
nected to the V
EE
plane. Since the RSET voltage compensation circuit is referenced to V
EE
, the RSET voltage will
track 1:1 with V
EE
changes, thus the voltage across the RSET resistor will remain constant.
RTCO
1
, RTCO
2
Terminals for positive temperature tracking resistor. This resistor controls the temperature tracking rate of the voltage
at the RSET pin, which in turn sets the LED drive current tracking. If the two pins are shorted together, the nominal
tracking rate is 1.4mV/
°
C and when a 2 k resistor is connected across the pins, the nominal tracking rate is
4.9 mV/
°
C.
V
CC
Most positive power supply input. +5 V for PECL operation or ground for standard ECL operation.
V
EE
Most negative power supply input. Ground for PECL operation or
5.2 V for standard ECL operation.
V
BB
Reference voltage for use in single ended applications or when the input signal is AC coupled into the device.
相關PDF資料 |
PDF描述 |
|---|---|
| MC10SX1130DR2G | LED Driver |
| MC10SX1189DG | Fibre Channel Coaxial Cable Driver and Loop Resiliency Circuit |
| MC10SX1189DR2 | Fibre Channel Coaxial Cable Driver and Loop Resiliency Circuit |
| MC10SX1189DR2G | Fibre Channel Coaxial Cable Driver and Loop Resiliency Circuit |
| MC10SX1190DTG | Fibre Channel Coaxial Cable Driver and Loop Resiliency Circuit |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC10SX1130DR2G | 功能描述:LED照明驅動器 BBG ECL COAX CABL RoHS:否 制造商:STMicroelectronics 輸入電壓:11.5 V to 23 V 工作頻率: 最大電源電流:1.7 mA 輸出電流: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:SO-16N |
| MC10SX1189D | 功能描述:緩沖器和線路驅動器 Fiber Channel Coax RoHS:否 制造商:Micrel 輸入線路數量:1 輸出線路數量:2 極性:Non-Inverting 電源電壓-最大:+/- 5.5 V 電源電壓-最小:+/- 2.37 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Reel |
| MC10SX1189DG | 功能描述:緩沖器和線路驅動器 Fiber Channel Coax Calbe Driver RoHS:否 制造商:Micrel 輸入線路數量:1 輸出線路數量:2 極性:Non-Inverting 電源電壓-最大:+/- 5.5 V 電源電壓-最小:+/- 2.37 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Reel |
| MC10SX1189DR2 | 功能描述:緩沖器和線路驅動器 Fiber Channel Coax RoHS:否 制造商:Micrel 輸入線路數量:1 輸出線路數量:2 極性:Non-Inverting 電源電壓-最大:+/- 5.5 V 電源電壓-最小:+/- 2.37 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Reel |
| MC10SX1189DR2G | 功能描述:緩沖器和線路驅動器 Fiber Channel Coax Calbe Driver RoHS:否 制造商:Micrel 輸入線路數量:1 輸出線路數量:2 極性:Non-Inverting 電源電壓-最大:+/- 5.5 V 電源電壓-最小:+/- 2.37 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。