![](http://datasheet.mmic.net.cn/ON-Semiconductor/MC10EP16DTR2_datasheet_105910/MC10EP16DTR2_6.png)
MC10EP16, MC100EP16
http://onsemi.com
6
Table 9. 100EP DC CHARACTERISTICS, NECL VCC = 0 V; VEE = 5.5 V to 3.0 V (Note 18) 40°C
25°C
85°C
Symbol
Characteristic
Min
Typ
Max
Min
Typ
Max
Min
Typ
Max
Unit
IEE
Power Supply Current
17
25
36
17
25
36
22
26
38
mA
VOH
Output HIGH Voltage (Note
19)1145 1020
895
1145 1020
895
1145 1020
895
mV
VOL
Output LOW Voltage (Note
19)1945 1820 1695 1945 1820 1695 1945 1820 1695
mV
VIH
Input HIGH Voltage (SingleEnded)
1225
880
1225
880
1225
880
mV
VIL
Input LOW Voltage (SingleEnded)
1945
1625 1945
1625
mV
VBB
Output Voltage Reference
1525 1425 1325 1525 1425 1325 1525 1425 1325
mV
VIHCMR
Input HIGH Voltage Common Mode
Range (Differential Configuration)
VEE + 2.0
0.0
VEE + 2.0
0.0
VEE + 2.0
0.0
V
IIH
Input HIGH Current
150
mA
IIL
Input LOW Current
D
0.5
150
0.5
150
0.5
150
mA
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
18.Input and output parameters vary 1:1 with VCC.
19.All loading with 50 W to VCC 2.0 V.
20.VIHCMR min varies 1:1 with VEE, VIHCMR max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential
input signal.
Table 10. AC CHARACTERISTICS VCC = 0 V; VEE = 3.0 V to 5.5 V or VCC = 3.0 V to 5.5 V; VEE = 0 V (Note 21) 40°C
25°C
85°C
Symbol
Characteristic
Min
Typ
Max
Min
Typ
Max
Min
Typ
Max
Unit
fmax
Maximum Frequency (Figure
2)> 4
GHz
tPLH,
tPHL
Propagation Delay to
Output Differential
150
220
280
150
220
280
160
240
300
ps
tSKEW
Duty Cycle Skew (Note
22)5.0
20
5.0
20
5.0
20
ps
tJITTER
CycletoCycle Jitter (Figure
2)0.2
< 1
0.2
< 1
0.2
< 1
ps
VPP
Input Voltage Swing
(Differential Configuration)
150
800
1200
150
800
1200
150
800
1200
mV
tr
tf
Output Rise/Fall Times
Q, Q
(20% 80%)
70
120
170
80
130
180
100
150
200
ps
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
21.Measured using a 750 mV source, 50% duty cycle clock source. All loading with 50 W to VCC 2.0 V.
22.Skew is measured between outputs under identical transitions. Duty cycle skew is defined only for differential operation when the delays
are measured from the cross point of the inputs to the cross point of the outputs.