*1 : The parameter is based on AVSS = V
參數資料
型號： MB95F128DPMC-GE1
廠商： Fujitsu Semiconductor America Inc
文件頁數： 26/67頁
文件大?。?/td> 0K
描述： IC MCU FLASH 60K ROM 100LQFP
標準包裝： 1
系列： F²MC MB95120
核心處理器： F²MC-8FX
芯體尺寸： 8-位
速度： 16MHz
連通性： I²C，LIN，SIO，UART/USART
外圍設備： LCD，LVD，POR，PWM，WDT
輸入/輸出數： 87
程序存儲器容量： 60KB（60K x 8）
程序存儲器類型： 閃存
RAM 容量： 2K x 8
電壓 - 電源 (Vcc/Vdd)： 1.8 V ~ 3.3 V
數據轉換器： A/D 12x8/10b
振蕩器型： 外部
工作溫度： -40°C ~ 85°C
封裝/外殼： 100-LQFP
包裝： 托盤
其它名稱： 865-1072
MB95120 Series
32
(Continued)
*1 : The parameter is based on AVSS
= VSS = 0.0 V.
*2 : Apply equal potential to AVcc and Vcc. AVR should not exceed AVcc
+ 0.3 V.
*3 : V0 to V3 should not exceed VCC
+ 0.3 V.
*4 : VI1 and Vo should not exceed VCC
+ 0.3 V. VI1 must not exceed the rating voltage. However, if the maximum
current to/from an input is limited by some means with external components, the ICLAMP rating supersedes the
VI1 rating.
*5 : Applicable to pins : P00 to P07, P10 to P14, P20 to P24, P30 to P37, P40 to P43, P52, P53
Use within recommended operating conditions.
Use at DC voltage (current).
+B signal is an input signal that exceeds VCC voltage. The + B signal should always be applied a limiting
resistance placed between the
+ B signal and the microcontroller.
The value of the limiting resistance should be set so that when the + B signal is applied the input current
to the microcontroller pin does not exceed rated values, either instantaneously or for prolonged periods.
Note that when the microcontroller drive current is low, such as in the power saving modes, the +B input
potential may pass through the protective diode and increase the potential at the VCC pin, and this affects
other devices.
Note that if the + B signal is inputted when the microcontroller power supply is off (not fixed at 0 V), the power
supply is provided from the pins, so that incomplete operation may result.
Note that if the + B input is applied during power-on, the power supply is provided from the pins and the
resulting power supply voltage may not be sufficient to operate the power-on reset.
Care must be taken not to leave the + B input pin open.
Note that analog system input/output pins other than the A/D input pins (LCD drive pins, etc.) cannot accept
+B signal input.
Parameter
Symbol
Rating
Unit
Remarks
Min
Max
“H” level average
current
IOHAV1
4
mA
Other than P00 to P07
Average output current
=
operating current
× operating ratio
(1 pin)
IOHAV2
8
P00 to P07
Average output current
=
operating current
× operating ratio
(1 pin)
“H” level total maximum
output current
ΣIOH
100
mA
“H” level total average
output current
ΣIOHAV
50
mA
Total average output current
=
operating current
× operating ratio
(Total of pins)
Power consumption
Pd
320
mW
Operating temperature
TA
40
+ 85
°C
Storage temperature
Tstg
55
+ 150
°C
相關PDF資料
PDF描述
MB95F128JBPF-GE1 IC MCU 60KB FLASH 100QFP
MB95F136JBWPF-GE1 IC MCU 32KB FLASH 28SOP
MB95F156JJPMC1-GE1 IC MCU FLASH 32K ROM 52LQFP
MB95F168JAPMC-GE1 IC MCU FLASH 60K ROM 64LQFP
MB95F204KP-G-SH-SNE2 IC MCU 16KB FLASH F2MC8FX 24SDIP
相關代理商/技術參數
參數描述
MB95F128E 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:8-bit Proprietary Microcontrollers
MB95F128EPF 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:8-bit Proprietary Microcontrollers
MB95F128EPMC 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:8-bit Proprietary Microcontrollers
MB95F128JB 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:8-bit Microcontrollers
MB95F128JBPF 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:8-bit Microcontrollers
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*