- 您現在的位置：買賣IC網 > PDF目錄45194 > MB91F487PF-GE1 (FUJITSU LTD) 32-BIT, FLASH, 80 MHz, RISC MICROCONTROLLER, PQFP100 PDF資料下載
參數資料
| 型號： | MB91F487PF-GE1 |
| 廠商： | FUJITSU LTD |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 32-BIT, FLASH, 80 MHz, RISC MICROCONTROLLER, PQFP100 |
| 封裝： | 14 X 20 MM, 3.35 MM HEIGHT, 0.65 MM PITCH, PLASTIC, QFP-100 |
| 文件頁數： | 19/96頁 |
| 文件大?。?/td> | 2461K |
| 代理商： | MB91F487PF-GE1 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁
MB91470/480 Series
26
DS07–16901–9E
■ HANDLING DEVICES
Preventing latch-up
Latch-up phenomenon may occur with CMOS IC, when a voltage higher than VCC or lower than VSS is applied
to either the input or output terminals, or when a voltage is applied between VCC pin and VSS pin that
exceeds the rated voltage. When latch-up occurs, a significant power-supply current surge results, which
may damage some elements due to the excess heat, so great care must be taken to ensure that the maximum
rating is never exceeded during use.
Treatment of unused input pins
Do not leave an unused input pin open, since it may cause a malfunction. Handle by, for example, using a
pull-up or pull-down resistor.
Power pins
In products with multiple VCC and VSS pins, the pins of the same potential are internally connected in the device
to avoid abnormal operations including latch-up. However, you must connect the pins to the same potential
power supply and a ground line externally to lower the electro-magnetic emission level, to prevent abnormal
operation of strobe signals caused by the rise in the ground level, and to conform to the total output current
rating.
Moreover, connect the current supply source with the VCC and VSS pins of this device at the low impedance.
It is also advisable to connect a ceramic capacitor of approximately 0.1
μF as a bypass capacitor between VCC
and VSS near this device.
Crystal oscillator circuit
Noise near the X0 and X1 pins may cause the device to malfunction. Design the printed circuit board so that
X0,X1, the crystal oscillator (or ceramic oscillator), and the bypass capacitor to ground are located as close
to the device as possible.
It is strongly recommended to design the PC board artwork with the X0 and X1pins surrounded by ground
plane because stable operation can be expected with such a layout. Please ask the crystal maker to eval-
uate the oscillational characteristics of the crystal and this device.
About mode pins (MD0 to MD2)
These pins should be connected directly to VCC pin or VSS pin.
Design the printed circuit board such that the pull-up/down resistance stays low, as well as the distance
between the mode pins and power supply or GND pins is as short as possible and the connection impedance
is low, when the pins are pulled-up/down such as for switching the pin level and rewriting the Flash memory
data. It is because of preventing the device erroneously switching to test mode due to noise.
Operation at start-up
Be sure to execute setting initialized reset (INIT) with INITX pin immediately after start-up.
Immediately after that, also, hold the "L"-level input to the INITX pin for the stabilization wait time required
for the oscillator circuit to take the oscillation stabilization wait time for the oscillator circuit and the stabiliza-
tion wait time for the regulator (For INIT via the INITX pin, the oscillation stabilization wait time setting is
initialized to the minimum value).
相關PDF資料 |
PDF描述 |
|---|---|
| MB91F486PF-GE1 | 32-BIT, FLASH, 80 MHz, RISC MICROCONTROLLER, PQFP100 |
| MB91487PMC-GE1 | 32-BIT, MROM, 80 MHz, RISC MICROCONTROLLER, PQFP100 |
| MB91486PF-GE1 | 32-BIT, MROM, 80 MHz, RISC MICROCONTROLLER, PQFP100 |
| MB91F492PMC-GE1 | 32-BIT, FLASH, 50 MHz, RISC MICROCONTROLLER, PQFP64 |
| MB91F492PMC1-GE1 | 32-BIT, FLASH, 50 MHz, RISC MICROCONTROLLER, PQFP64 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MB91F487PMC-GE1 | 功能描述:IC MCU 512KB FLASH 100-LQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:FR MB91480 標準包裝:38 系列:Encore!® XP® 核心處理器:eZ8 芯體尺寸:8-位 速度:5MHz 連通性:IrDA，UART/USART 外圍設備:欠壓檢測/復位，LED，POR，PWM，WDT 輸入/輸出數:16 程序存儲器容量:4KB（4K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:1K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 3.6 V 數據轉換器:- 振蕩器型:內部 工作溫度:-40°C ~ 105°C 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 包裝:管件 其它名稱:269-4116Z8F0413SH005EG-ND |
| MB91F492PMC-GE1 | 功能描述:IC MCU 256KB FLASH FR60 LFQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:FR MB91490 產品培訓模塊:The Ultra-Low Power MSP430 MSP430 Overview MSP430 Design Tools MSP430 Peripherals MSP430x2xx/4xx and Wireless Overview Portable Medical Solutions with MSP430 MSP430 for Utility Metering Solutions MSP430: How to JTAG MSP430, How To Use the Clock System Grace Software Graphical User Interface MCU Overview Driver Library MSP430Ware Overview 標準包裝:1 系列:MSP430x4xx 核心處理器:RISC 芯體尺寸:16-位 速度:8MHz 連通性:SPI，UART/USART 外圍設備:欠壓檢測/復位，LCD，POR，PWM，WDT 輸入/輸出數:48 程序存儲器容量:32KB（32K x 8 + 256B） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:1K x 8 電壓 - 電源 (Vcc/Vdd):1.8 V ~ 3.6 V 數據轉換器:A/D 8x12b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:100-LQFP 包裝:Digi-Reel® 其它名稱:296-26232-6 |
| MB91F585 | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32-bit Motor Control MCU for Electric (EV) and Hybrid Electric Vehicles (HEV) |
| MB91F587 | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32-bit Motor Control MCU for Electric (EV) and Hybrid Electric Vehicles (HEV) |
| MB91F591 | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32-bit MCU with Integrated Graphics Controller SoC |
發布緊急采購，3分鐘左右您將得到回復。