- 您現在的位置：買賣IC網 > PDF目錄45192 > MB90F598GPF 16-BIT, FLASH, 16 MHz, MICROCONTROLLER, PQFP100 PDF資料下載
參數資料
| 型號： | MB90F598GPF |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 16-BIT, FLASH, 16 MHz, MICROCONTROLLER, PQFP100 |
| 封裝： | PLASTIC, QFP-100 |
| 文件頁數： | 27/52頁 |
| 文件大?。?/td> | 657K |
| 代理商： | MB90F598GPF |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁當前第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁
MB90595/595G Series
33
(Continued)
*6:
Applicable to pins : P00 to P07, P10 to P17, P20 to P27, P30 to P37, P40 to P47, P50 to P57, P70 to P77,
P80 to P87, P90 to P95
Use within recommended operating conditions.
Use at DC voltage (current) .
The +B signal should always be applied with a limiting resistance placed between the +B signal and the
microcontroller.
The value of the limiting resistance should be set so that when the +B signal is applied the input current to
the microcontroller pin does not exceed rated values, either instantaneously or for prolonged periods.
Note that when the microcontroller drive current is low, such as in the power saving modes, the +B input
potential may pass through the protective diode and increase the potential at the VCC pin, and this may affect
other devices.
Note that if a +B signal is input when the microcontroller current is off (not fixed at 0 V) , the power supply is
provided from the pins, so that incomplete operation may result.
Note that if the +B input is applied during power-on, the power supply is provided from the pins and the
resulting supply voltage may not be sufficient to operate the power-on result.
Care must be taken not to leave the +B input pin open.
Note that analog system input/output pins other than the A/D input pins (LCD drive pins, comparator input
pins, etc.) cannot accept
+B signal input.
Sample recommended circuits :
Note: Average output current = operating current
× operating efficiency
WARNING: Semiconductor devices can be permanently damaged by application of stress (voltage, current,
temperature, etc.) in excess of absolute maximum ratings. Do not exceed these ratings.
P-ch
N-ch
VCC
R
Input/Output Equivalent circuits
+B input (0 V to 16 V)
Limiting
resistance
Protective diode
相關PDF資料 |
PDF描述 |
|---|---|
| MB90F803PF-G | 16-BIT, FLASH, 25 MHz, MICROCONTROLLER, PQFP100 |
| MB90F809PF-G | 16-BIT, FLASH, 25 MHz, MICROCONTROLLER, PQFP100 |
| MB90803PF-G | 16-BIT, MROM, 25 MHz, MICROCONTROLLER, PQFP100 |
| MB90F823PF | 16-BIT, FLASH, 24 MHz, MICROCONTROLLER, PQFP80 |
| MB90F822PFM | 16-BIT, FLASH, 24 MHz, MICROCONTROLLER, PQFP80 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MB90F598GPFR-GE1 | 制造商:FUJITSU 功能描述: |
| MB90F598GPFR-GSE1 | 功能描述:IC MCU 16BIT 制造商:cypress semiconductor corp 系列:F2MC-16LX MB90595G 包裝:托盤 零件狀態:在售 核心處理器:F2MC-16LX 核心尺寸:16-位 速度:16MHz 連接性:CAN，EBI/EMI，SCI，串行輸入/輸出，UART/USART 外設:POR，PWM，WDT I/O 數:78 程序存儲容量:128KB（128K x 8） 程序存儲器類型:閃存 EEPROM 容量:- RAM 容量:4K x 8 電壓 - 電源（Vcc/Vdd）:3 V ~ 5.5 V 數據轉換器:A/D 8x8/10b 振蕩器類型:外部 工作溫度:-40°C ~ 85°C（TA） 封裝/外殼:100-BQFP 供應商器件封裝:100-PQFP（20x14） 標準包裝:66 |
| MB90F598PFR-GE1 | 制造商:FUJITSU 功能描述: |
| MB90F804-201PFR-GE1 | 制造商:FUJITSU 功能描述: |
| MB90F867APFR-G-SNE1 | 制造商:FUJITSU 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。