參數資料
型號： MB90F481PFV
元件分類： 微控制器/微處理器
英文描述： 16-BIT, FLASH, 25 MHz, MICROCONTROLLER, PQFP100
封裝： PLASTIC, LQFP-100
文件頁數： 7/101頁
文件大?。?/td> 1063K
代理商： MB90F481PFV
MB90480 Series
13
s HANDLING DEVICES
1.
Power-on and Preventing Latch-up
CMOS IC devices are subject to the phenomenon known as latch-up in conditions such as the following.
(1) When voltage higher than VCC or lower than VSS are applied to input pins or output pins.
(2) When voltages higher than rated voltage levels are applied between VCC and VSS.
(3) When the AVCC power supply is applied before the VCC power.
Power to an analog system must always be turned on at the same time as the VCC power supply, or after the
digital power supply is on. (Analog power must also be turned off before or at the same time as other power.)
When latch-up occurs, power supply current increases rapidly, resulting in thermal damage to circuit elements.
2.
Treatment of Unused Pins
Leaving unused input pins unconnected can cause abnormal operation. Unused input pins should always be
pulled up or down.When the A/D converter is not in use, be sure to make the necessary connections
AVCC
= AVRH = VCC, and AVSS = VSS.
3.
Notes on Using External Clock
Connections for external clock use :
4.
Treatment of Power Supply Pins (VCC/VSS)
When multiple VCC/VSS pins are present, device design considerations for prevention of latch-up and unwanted
electromagnetic interference, abnormal storobe signal operation due to ground level rise, and conformity with
total output current ratings require that all power supply pins must be externally connected to power supply or
ground.
Consideration should be given to connecting power supply sources to the VCC/VSS terminals of this device with
as low impedane as possible. It is also recommended that a bypass capacitor of approximately 0.1
F be placed
between the VCC and VSS lines as close to this device as possible.
5.
Crystal Oscillator Circuits
Noise around the X0/X1, or X0A/X1A pins may cause this device to operate abnormally. In the interest of stable
operation it is strongly recommended that printed circuit artwork places ground bypass capacitors as close as
possible to the X0/X1, X0A/X1A and crystal oscillator (or ceramic oscillator) and that oscillator lines do not cross
the lines of other circuits.
6.
Notes on during operation of PLL clock mode
If the PLL clock mode is selected, the microcontroller attempt to be working with the self-oscillating circuit even
when there is no external oscillator or external clock input is stopped. Performance of this operation, however,
cannot be guaranteed.
X0
X1
OPEN
相關PDF資料
PDF描述
MB90F482PF 16-BIT, FLASH, 25 MHz, MICROCONTROLLER, PQFP100
MB90F483PFV 16-BIT, FLASH, 25 MHz, MICROCONTROLLER, PQFP100
MB90F483PF 16-BIT, FLASH, 25 MHz, MICROCONTROLLER, PQFP100
MB90F497PFM 16-BIT, FLASH, 16 MHz, MICROCONTROLLER, PQFP64
MB90F523PFF-G 16-BIT, FLASH, 16 MHz, MICROCONTROLLER, PQFP120
相關代理商/技術參數
參數描述
MB90F482PFR-GE1 制造商:FUJITSU 功能描述:
MB90F482PFR-G-JNE1 制造商:FUJITSU 功能描述:
MB90F482PMC-G-JNE1 制造商:FUJITSU 功能描述:
MB90F497GPMC-GE1 功能描述:IC MCU 16BIT 制造商:cypress semiconductor corp 系列:F2MC-16LX MB90495G 包裝:托盤 零件狀態:在售 核心處理器:F2MC-16LX 核心尺寸:16-位 速度:16MHz 連接性:CAN，EBI/EMI，SCI，UART/USART 外設:POR，WDT I/O 數:49 程序存儲容量:64KB（64K x 8） 程序存儲器類型:閃存 EEPROM 容量:- RAM 容量:2K x 8 電壓 - 電源（Vcc/Vdd）:4.5 V ~ 5.5 V 數據轉換器:A/D 8x8/10b 振蕩器類型:外部 工作溫度:-40°C ~ 105°C（TA） 封裝/外殼:64-LQFP 供應商器件封裝:64-LQFP（12x12） 標準包裝:119
MB90F497GPMCR-G 制造商:FUJITSU 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*