- 您現在的位置：買賣IC網 > PDF目錄45191 > MB90F367TSPMT 16-BIT, FLASH, 24 MHz, MICROCONTROLLER, PQFP48 PDF資料下載
參數資料
| 型號： | MB90F367TSPMT |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 16-BIT, FLASH, 24 MHz, MICROCONTROLLER, PQFP48 |
| 封裝： | PLASTIC, LQFP-48 |
| 文件頁數： | 32/59頁 |
| 文件大?。?/td> | 623K |
| 代理商： | MB90F367TSPMT |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁當前第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁
MB90360 Series
38
(Continued)
*1 : This parameter is based on VSS
= AVSS = 0 V.
*2 : Set AVCC and VCC to the same voltage. Make sure that AVCC does not exceed VCC and that the voltage at the
analog inputs does not exceed AVCC when the power is switched on.
*3 : VI and VO should not exceed VCC
+ 0.3 V. VI should not exceed the specified ratings. However, if the maximun
current to/from an input is limited by some means with external components, the ICLAMP rating supersedes the
VI rating.
*4 : Applicable to pins : P24 to P27, P40 to P44, P50 to P57, P60 to P67, P80, P82 to P87
*5 : Applicable to pins : P20 to P23
*6 : Applicable to pins : P20 to P27, P40 to P44, P50 to P57, P60 to P67, P80, P82 to P87
Use within recommended operating conditions.
Use at DC voltage (current) .
The +B signal should always be applied a limiting resistance placed between the +B signal and the
microcontroller.
The value of the limiting resistance should be set so that when the +B signal is applied the input current to
the microcontroller pin does not exceed rated values, either instantaneously or for prolonged periods.
Note that when the microcontroller drive current is low, such as in the power saving modes, the +B input
potential may pass through the protective diode and increase the potential at the VCC pin, and this may affect
other devices.
Note that if a +B signal is inputted when the microcontroller power supply is off (not fixed at 0 V) , the power
supply is provided from the pins, so that incomplete operation may result.
Note that if the +B input is applied during power-on, the power supply is provided from the pins and the
resulting power supply voltage may not be sufficient to operate the power-on reset.
Care must be taken not to leave the +B input pin open.
Sample recommended circuits :
*7 : If used exceeding TA
= +105 °C, please contact Fujitsu for reliability limitations.
WARNING: Semiconductor devices can be permanently damaged by application of stress (voltage, current,
temperature, etc.) in excess of absolute maximum ratings. Do not exceed these ratings.
Pch
Nch
VCC
R
Input/output equivalent circuits
+B input (0 V to 16 V)
Limiting
resistance
Protective diode
相關PDF資料 |
PDF描述 |
|---|---|
| MB90367SPMT | 16-BIT, MROM, 24 MHz, MICROCONTROLLER, PQFP48 |
| MB90F362TPMT | 16-BIT, FLASH, 24 MHz, MICROCONTROLLER, PQFP48 |
| MB90362PMT | 16-BIT, MROM, 24 MHz, MICROCONTROLLER, PQFP48 |
| MB90362TSPMT | 16-BIT, MROM, 24 MHz, MICROCONTROLLER, PQFP48 |
| MB90F362SPMT | 16-BIT, FLASH, 24 MHz, MICROCONTROLLER, PQFP48 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MB90F387PMCR-GSE1 | 制造商:FUJITSU 功能描述: |
| MB90F387PMT-GSE1 | 功能描述:IC MCU FLASH 64K ROM 48LQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:F²MC MB90385 產品培訓模塊:MCU Product Line Introduction XMEGA Introduction AVR XMEGA USB Connectivity 標準包裝:90 系列:AVR® XMEGA 核心處理器:AVR 芯體尺寸:8/16-位 速度:32MHz 連通性:I²C，IrDA，SPI，UART/USART 外圍設備:欠壓檢測/復位，DMA，POR，PWM，WDT 輸入/輸出數:50 程序存儲器容量:192KB（96K x 16） 程序存儲器類型:閃存 EEPROM 大小:4K x 8 RAM 容量:16K x 8 電壓 - 電源 (Vcc/Vdd):1.6 V ~ 3.6 V 數據轉換器:A/D 16x12b; D/A 2x12b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:64-TQFP 包裝:托盤 配用:ATSTK600-RC14-ND - STK600 SOCKET/ADAPTER 64TQFPATSTK600-TQFP64-ND - STK600 SOCKET/ADAPTER 64-TQFPATAVRONEKIT-ND - KIT AVR/AVR32 DEBUGGER/PROGRMMRATAVRISP2-ND - PROGRAMMER AVR IN SYSTEM |
| MB90F387SPMCR-GE1 | 制造商:FUJITSU 功能描述: |
| MB90F387SPMCR-G-JNE1 | 制造商:FUJITSU 功能描述: |
| MB90F387SPMCRGSE1 | 制造商:FUJITSU 功能描述:Pb Free |
發布緊急采購，3分鐘左右您將得到回復。