- 您現在的位置：買賣IC網 > PDF目錄45185 > MB89P485L-102PMC (FUJITSU LTD) MICROCONTROLLER, PQFP64 PDF資料下載
參數資料
| 型號： | MB89P485L-102PMC |
| 廠商： | FUJITSU LTD |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | MICROCONTROLLER, PQFP64 |
| 封裝： | 12 X 12 MM, 1.70 MM HEIGHT, 0.65 MM PITCH, PLASTIC, LQFP-64 |
| 文件頁數： | 7/56頁 |
| 文件大小： | 1476K |
| 代理商： | MB89P485L-102PMC |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁
MB89480 Series
DS07-12559-2E
15
■ HANDLING DEVICES
1.
Preventing Latch-up
Latch-up may occur on CMOS IC if voltage higher than VCC or lower than VSS is applied to input and output pins
other than medium- to high-voltage pins or if higher than the voltage which shows on “1. Absolute Maximum
Ratings” in
■ ELECTRICAL CHARACTERISTICS is applied between VCC and VSS.
When latch-up occurs, power supply current increases rapidly and might thermally damage elements. When
using, take great care not to exceed the absolute maximum ratings.
Also, take care to prevent the analog power supply (AVCC) and analog input from exceeding the digital power
supply (VCC) when the analog system power supply is turned on and off.
2.
Treatment of Unused Input Pins
Leaving unused input pins open could cause malfunctions. They should be connected to a pull-up or pull-down
resistor.
3.
Treatment of Power Supply Pins on Microcontrollers with A/DConverter
Connect to be AVCC = VCC and AVSS = VSS even if the A/D converter is not in use.
4.
Treatment of N.C. Pins
Be sure to leave (internally connected) N.C. pins open.
5.
Power Supply Voltage Fluctuations
Although VCC power supply voltage is assured to operate within the rated range, a rapid fluctuation of the voltage
could cause malfunctions, even if it occurs within the rated range. Stabilizing voltage supplied to the IC is therefore
important. As stabilization guidelines, it is recommended to control power so that VCC ripple fluctuations (P-P
value) will be less than 10% of the standard VCC value at the commercial frequency (50 to 60 Hz) and the transient
fluctuation rate will be less than 0.1 V/ms at the time of a momentary fluctuation such as when power is switched.
6.
Precautions when Using an External Clock
Even when an external clock is used, oscillation stabilization time is required for power-on reset and wake-up
from stop mode.
7.
Notes on noise in the External Reset Pin (RST)
If the reset pulse applied to the external reset pin (RST) does not meet the specifications, it may cause malfunc-
tions. Use caution so that the reset pulse less than the specifications will not be fed to the external reset pin (RST).
相關PDF資料 |
PDF描述 |
|---|---|
| MB89P485L-103PMC | MICROCONTROLLER, PQFP64 |
| MB89485PMC | MICROCONTROLLER, PQFP64 |
| MB89485LPMC | MICROCONTROLLER, PQFP64 |
| MB89P485-101PMC | MICROCONTROLLER, PQFP64 |
| MB89P538PF-101 | 8-BIT, OTPROM, 12.5 MHz, MICROCONTROLLER, PQFP64 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MB89P485L-102P-SH | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:8-bit Proprietary Microcontroller |
| MB89P485L-103PFM | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:8-bit Proprietary Microcontroller |
| MB89P485L-103PFM-G-JNE1 | 制造商:FUJITSU 功能描述:8-Bit MCU 制造商:FUJITSU 功能描述:8-bit Proprietary Microcontroller |
| MB89P485L-103P-SH | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:8-bit Proprietary Microcontroller |
| MB89P485L-104PFM | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:8-bit Proprietary Microcontroller |
發(fā)布緊急采購，3分鐘左右您將得到回復。