參數資料
型號: MAXQ612G-0000+
廠商: Maxim Integrated Products
文件頁數: 22/35頁
文件大?。?/td> 0K
描述: IC MCU 16BIT 128KB IR MOD 64LQFP
產品培訓模塊: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝: 160
系列: MAXQ®
核心處理器: RISC
芯體尺寸: 16-位
速度: 12MHz
連通性: I²C,SPI,UART/USART
外圍設備: 欠壓檢測/復位,紅外線,電源故障,POR,WDT
輸入/輸出數: 44
程序存儲器容量: 128KB(128K x 8)
程序存儲器類型: 閃存
RAM 容量: 6K x 8
電壓 - 電源 (Vcc/Vdd): 1.7 V ~ 3.6 V
振蕩器型: 內部
工作溫度: 0°C ~ 70°C
封裝/外殼: 64-LQFP
包裝: 托盤
29
Maxim Integrated
16-Bit Microcontrollers with
Infrared Module and Optional USB
MAXQ612/MAXQ622
mode to minimize power consumption. This feature is
enabled using the power-fail monitor disable (PFD) bit
in the PWCN register. The reset default state for the PFD
bit is 1, which disables the power-fail monitor function
during stop mode. If power-fail monitoring is disabled
(PFD = 1) during stop mode, the circuitry responsible
for generating a power-fail warning or reset is shut down
and neither condition is detected. Thus, the VDD < VRST
condition does not invoke a reset state. However, in the
event that VDD falls below the POR level, a POR is gen-
erated. The power-fail monitor is enabled prior to stop
mode exit and before code execution begins. If a power-
fail warning condition (VDD < VPFW) is then detected,
the power-fail interrupt flag is set on stop mode exit. If a
power-fail reset condition is detected (VDD < VRST), the
CPU goes into reset.
Power-Fail Warning
The power-fail monitor can assert an interrupt if the volt-
age falls below a configurable threshold between the
operating voltage and the reset voltage. This, if enabled,
can allow the firmware to perform housekeeping tasks if
the voltage level decays below the warning threshold.
The power-fail threshold value should only be changed
when the power-fail warning interrupt is disabled (CKCN.
PFIE = 0) to prevent unintended triggering of the power-
fail warning condition.
The power-fail warning threshold is reset to 1.8V by a
POR and is not affected by other resets. See Table 4.
Power-Fail Detection
Figures 5, 6, and 7 show the power-fail detection and
response during normal and stop-mode operation.
If a reset is caused by a power-fail, the power-fail monitor
can be set to one of the following intervals:
Always on—continuous monitoring
211 nanopower ring oscillator clocks (~256ms)
212 nanopower ring oscillator clocks (~512ms)
213 nanopower ring oscillator clocks (~1.024s)
In the case where the power-fail circuitry is periodically
turned on, the power-fail detection is turned on for two
Table 4. Power-Fail Warning Level Selection
Figure 5. Power-Fail Detection During Normal Operation
A
B
C
D
F
G
H
I
E
VDD
VPFW
VRST
VPOR
INTERNAL RESET
(ACTIVE HIGH)
t
< tPFW
t
≥ tPFW
t
≥ tPFW
t
≥ tPFW
PWCN.PFWARNCN[1:0]
PFW THRESHOLD
(V)
00
1.8
01
1.9
10
2.55
11
2.75
相關PDF資料
PDF描述
VI-25T-CV-S CONVERTER MOD DC/DC 6.5V 150W
ISD1750EYIR IC VOICE REC/PLAY 50SEC 28-TSOP
ISD1740EYIR IC VOICE REC/PLAY 40SEC 28-TSOP
ISD1750EYR IC VOICE REC/PLAY 50SEC 28-TSOP
ISD1740SYR IC VOICE REC/PLAY 40SEC 28-SOIC
相關代理商/技術參數
參數描述
MAXQ612G-0000+ 功能描述:16位微控制器 - MCU 16-Bit MCU w/Infrared Module RoHS:否 制造商:Texas Instruments 核心:RISC 處理器系列:MSP430FR572x 數據總線寬度:16 bit 最大時鐘頻率:24 MHz 程序存儲器大小:8 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:VQFN-40 安裝風格:SMD/SMT
MAXQ612J-0000 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:16-Bit Microcontrollers with Infrared Module and Optional USB
MAXQ612J-0000+ 功能描述:16位微控制器 - MCU 16-Bit MCU w/Infrared Module RoHS:否 制造商:Texas Instruments 核心:RISC 處理器系列:MSP430FR572x 數據總線寬度:16 bit 最大時鐘頻率:24 MHz 程序存儲器大小:8 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:VQFN-40 安裝風格:SMD/SMT
MAXQ612J-UEI+ 制造商:Maxim Integrated Products 功能描述:MAXQ612 BLANK 44 TQFN FW SCRT UEI - Rail/Tube
MAXQ612X-UEI+ 制造商:Maxim Integrated Products 功能描述:MAXQ612 BLANK BARE DIE FW SCRT UEI - Gel-pak, waffle pack, wafer, diced wafer on film