- 您現在的位置：買賣IC網 > PDF目錄3367 > MAX9938TEBS+TG45 (Maxim Integrated Products)IC AMP CURRENT SENSE 4UCSP PDF資料下載
參數資料
| 型號： | MAX9938TEBS+TG45 |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 12/14頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC AMP CURRENT SENSE 4UCSP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 2,500 |
| 放大器類型： | 電流檢測 |
| 電路數： | 1 |
| -3db帶寬： | 125kHz |
| 電壓 - 輸入偏移： | 100µV |
| 電流 - 電源： | 1.1µA |
| 電壓 - 電源，單路/雙路(±)： | 1.6 V ~ 28 V |
| 工作溫度： | -45°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 4-WFBGA，CSPBGA |
| 供應商設備封裝： | 4-UCSP（1.05x1.05） |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁當前第12頁第13頁第14頁
MAX9938
1A, 4-Bump UCSP/SOT23,
Precision Current-Sense Amplifier
_______________________________________________________________________________________
7
Applications Information
Choosing the Sense Resistor
Choose RSENSE based on the following criteria:
Voltage Loss
A high RSENSE value causes the power-source voltage
to drop due to IR loss. For minimal voltage loss, use the
lowest RSENSE value.
OUT Swing vs. VRS+ and VSENSE
The MAX9938 is unique since the supply voltage is the
input common-mode voltage (the average voltage at
RS+ and RS-). There is no separate VCC supply voltage
pin. Therefore, the OUT voltage swing is limited by the
minimum voltage at RS+.
VOUT(max) = VRS+ (min) - VSENSE (max) - VOH
and
VSENSE full scale should be less than VOUT/gain at the
minimum RS+ voltage. For best performance with a
3.6V supply voltage, select RSENSE to provide approxi-
mately 120mV (gain of 25V/V), 60mV (gain of 50V/V),
30mV (gain of 100V/V), or 15mV (gain of 200V/V) of
sense voltage for the full-scale current in each applica-
tion. These can be increased by use of a higher mini-
mum input voltage.
Accuracy
In the linear region (VOUT < VOUT(max)), there are two
components to accuracy: input offset voltage (VOS) and
gain error (GE). For the MAX9938, VOS = 500μV (max)
and gain error is 0.5% (max). Use the linear equation:
VOUT = (gain ± GE) x VSENSE ± (gain x VOS)
to calculate total error. A high RSENSE value allows lower
currents to be measured more accurately because off-
sets are less significant when the sense voltage is larger.
Efficiency and Power Dissipation
At high current levels, the I2R losses in RSENSE can be
significant. Take this into consideration when choosing
the resistor value and its power dissipation (wattage)
rating. Also, the sense resistor’s value might drift if it is
allowed to heat up excessively. The precision VOS of
the MAX9938 allows the use of small sense resistors to
reduce power dissipation and reduce hot spots.
Kelvin Connections
Because of the high currents that flow through RSENSE,
take care to eliminate parasitic trace resistance from
causing errors in the sense voltage. Either use a four-
terminal current-sense resistor or use Kelvin (force and
sense) PCB layout techniques.
Optional Output Filter Capacitor
When designing a system that uses a sample-and-hold
stage in the ADC, the sampling capacitor momentarily
loads OUT and causes a drop in the output voltage. If
sampling time is very short (less than a microsecond),
consider using a ceramic capacitor across OUT and
GND to hold VOUT constant during sampling. This also
decreases the small-signal bandwidth of the current-
sense amplifier and reduces noise at OUT.
Input Filters
Some applications of current-sense amplifiers need to
measure currents accurately even in the presence of both
differential and common-mode ripple, as well as a wide
variety of input transient conditions. For example, high-fre-
quency ripple at the output of a switching buck or boost
regulator results in a common-mode voltage at the inputs
of the MAX9938. Alternatively, fast load-current transients,
when measuring at the input of a switching buck or boost
regulator, can cause high-frequency differential sense
voltages to occur at the inputs of the MAX9938, although
the signal of interest is the average DC value. Such high-
frequency differential sense voltages may result in a volt-
age offset at the MAX9938 output.
R
V
GI
SENSE
OUT
LOAD
=
×
(max)
相關PDF資料 |
PDF描述 |
|---|---|
| IPT1-125-01-S-D-RA | CONN PLUG .100" 50POS DL PCB R/A |
| 961256-5900-AR-TP | CONN HEADER R/A 56POS GOLD SMD |
| 5VT 250-R | FUSE 250MA 250VAC 5X20 SLOW |
| 5VT 5-R | FUSE 5A 250VAC 5X20 SLOW |
| N4640-2000RB | 40/HDR/SMT/STR/FLG |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX9938TEUK+ | 制造商:Maxim Integrated Products 功能描述: |
| MAX9938TEUK+T | 功能描述:電流靈敏放大器 1uA Bump Precision Current Sense Amp RoHS:否 制造商:Texas Instruments 通道數量: 共模抑制比（最小值）:110 dB 輸入補償電壓:80 uV 電源電壓-最大:5.5 V 電源電壓-最小:2.7 V 電源電流:350 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-16 封裝:Reel |
| MAX9938WEBS+G45 | 制造商:Maxim Integrated Products 功能描述:1?A, 4-BUMP UCSP/SOT23, PRECISION CURRENT-SENSE AMPLIFIER - Rail/Tube |
| MAX9938WEBS+T | 功能描述:電流靈敏放大器 1 A 4-Bump UCSP/SOT23 Precision Current-Sense Amplifier RoHS:否 制造商:Texas Instruments 通道數量: 共模抑制比（最小值）:110 dB 輸入補償電壓:80 uV 電源電壓-最大:5.5 V 電源電壓-最小:2.7 V 電源電流:350 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-16 封裝:Reel |
| MAX9938WEBS+TG45 | 功能描述:電流靈敏放大器 Precision 1uA Current Sense Amp RoHS:否 制造商:Texas Instruments 通道數量: 共模抑制比（最小值）:110 dB 輸入補償電壓:80 uV 電源電壓-最大:5.5 V 電源電壓-最小:2.7 V 電源電流:350 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-16 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。