- 您現在的位置：買賣IC網 > PDF目錄11672 > MAX9921AUB+ (Maxim Integrated Products)IC SENSOR HALL EFFECT 10-MSOP PDF資料下載
參數資料
| 型號： | MAX9921AUB+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 4/16頁 |
| 文件大小： | 0K |
| 描述： | IC SENSOR HALL EFFECT 10-MSOP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 50 |
| 類型： | 霍爾效應傳感器 |
| 輸入類型： | 電壓 |
| 輸出類型： | 邏輯 |
| 接口： | 2 線 |
| 電流 - 電源： | 1.3mA |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 10-TFSOP，10-MSOP（0.118"，3.00mm 寬） |
| 供應商設備封裝： | 10-µMAX |
| 包裝： | 管件 |
第1頁第2頁第3頁當前第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁
MAX9921
Hall Input Short-to-Ground
The Hall input shorted-to-ground fault is effectively a
latched condition if the input remains loaded by the Hall
switch when the shorting condition is removed. The cur-
rent required to power the Hall switch is shut off and only
a 50A pullup current remains. The Hall input can be
manually re-energized or it can be re-energized by the
ECU. A falling edge at DIAG initiates a restart with a
blanking cycle of any Hall input that has been shut down
due to the shorted-to-ground condition. During startup or
restart, it is possible for a Hall input to charge up an exter-
nal capacitance of 0.02F without tripping into a shorted-
to-ground latched state. All other fault conditions are not
latched and when these other faults are removed, ERR
goes high and the Hall input is again functional.
Manual Method for Re-Energizing Hall Sensor
and Means for Diagnosing an Intermittent
Hall Sensor Connection
Figure 4 shows the behavior of the MAX9921 when a
Hall input is open. Figure 5 shows the behavior of the
MAX9921 when the open input is reconnected to a Hall
sensor. Figures 4 and 5 demonstrate how a shorted-to-
ground Hall input can be reset.
Resetting a shorted-to-ground Hall input involves
three steps:
1) Relieve the short to ground at the Hall sensor.
2) Disconnect the Hall input from the Hall sensor (open
input fault condition).
3) Reconnect the Hall input to the Hall sensor.
The MAX9921 restarts the Hall input with a blanking
cycle. If the Hall input is disconnected from the Hall
sensor for 10ms, it allows the Hall input to be pulled up
by the 50A pullup current to register the open-input
fault condition. Then, reconnecting the Hall input to the
Hall sensor restarts the Hall input with a blanking cycle.
This provides a manual means of re-energizing a Hall
input without having to resort to the ECU to reset it. This
also demonstrates that an intermittent connection to a
Hall sensor can recover without intervention of the ECU.
This gives the ECU a means of diagnosing an intermit-
tent connection to a Hall sensor by using the diagnostic
mode to detect a diagnostic sequence of “open-circuit”
to “blanking cycle” to “no fault.”
Dual, 2-Wire Hall-Effect Sensor Interface
with Diagnostics
12
______________________________________________________________________________________
14V
VIN_
IIN_
0V
HALL INPUT
SHORT TO
GROUND FAULT
INDICATED
HALL INPUT
OPEN-CIRCUIT
FAULT INDICATED
TIME
VBAT - 25mV
5mV/ms
TIME
50
A
0A
HALL INPUT
DISCONNECTED
FROM SENSOR
Figure 4. Hall Input Ramps to Open-Circuit Fault When Short to Ground is Relieved
相關PDF資料 |
PDF描述 |
|---|---|
| VI-BTL-IX-F3 | CONVERTER MOD DC/DC 28V 75W |
| VE-J3R-IY-F3 | CONVERTER MOD DC/DC 7.5V 50W |
| VI-BTL-IW-F2 | CONVERTER MOD DC/DC 28V 100W |
| VE-J3R-IY-F1 | CONVERTER MOD DC/DC 7.5V 50W |
| 413589-6 | CONN PLUG BNC RG-59DB CRIMP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX9921AUB/V+ | 功能描述:接口 - 專用 Dual Hall-Effect Sensor Interface RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| MAX9921AUB/V+C40 | 制造商:Maxim Integrated Products 功能描述:DUAL 2-WIRE HALL-EFFECT SENSOR INTERFACE WITH DIAGNOSTICS - Rail/Tube |
| MAX9921AUB/V+T | 功能描述:接口 - 專用 Dual Hall-Effect Sensor Interface RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| MAX9921AUB/V+TC40 | 制造商:Maxim Integrated Products 功能描述:DUAL, 2-WIRE HALL-EFFECT SENSOR INTERFACE WITH DIAGNOSTICS - Tape and Reel |
| MAX9921AUB+ | 功能描述:接口 - 專用 Dual Hall-Effect Sensor Interface RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
發布緊急采購，3分鐘左右您將得到回復。