參數資料
型號: MAX9914EXK+T
廠商: Maxim Integrated Products
文件頁數: 2/12頁
文件大?。?/td> 0K
描述: IC OP AMP RRIO SC70-5
產品培訓模塊: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝: 1
放大器類型: 通用
電路數: 1
輸出類型: 滿擺幅
轉換速率: 0.5 V/µs
增益帶寬積: 1MHz
電流 - 輸入偏壓: 1pA
電壓 - 輸入偏移: 200µV
電流 - 電源: 20µA
電流 - 輸出 / 通道: 15mA
電壓 - 電源,單路/雙路(±): 1.8 V ~ 5.5 V
工作溫度: -40°C ~ 85°C
安裝類型: 表面貼裝
封裝/外殼: 6-TSSOP(5 引線),SC-88A,SOT-353
供應商設備封裝: SC-70-5
包裝: 標準包裝
產品目錄頁面: 1392 (CN2011-ZH PDF)
其它名稱: MAX9914EXK+TDKR
MAX9914–MAX9917
1MHz, 20A, Rail-to-Rail
I/O Op Amps with Shutdown
10
Maxim Integrated
Power-Supply Considerations
The MAX9914–MAX9917 are optimized for single 1.8V
to 5.5V supply operation. A high amplifier power-supply
rejection ratio of 85dB (typ) allows the devices to be
powered directly from a battery, simplifying design and
extending battery life.
Power-Up Settling Time
The MAX9914–MAX9917 typically require 2s after
power-up. Supply settling time depends on the supply
voltage, the value of the bypass capacitor, the output
impedance of the incoming supply, and any lead resis-
tance or inductance between components. Op amp
settling time depends primarily on the output voltage
and is slew-rate limited. Figure 3 shows the MAX991_ in
a noninverting voltage follower configuration with the
input held at midsupply. The output settles in approxi-
mately 3.5s for VDD = 3V (see the Typical Operating
Characteristics for the Power-Up Settling Time graph).
Shutdown Mode
The MAX9915 and MAX9917 feature active-low shut-
down inputs. The MAX9915 and MAX9917 enter shut-
down in 2s (typ) and exit shutdown in 10s (typ). The
amplifiers’ outputs are high impedance in shutdown
mode. Drive SHDN low to enter shutdown. Drive SHDN
high to enable the amplifier. The MAX9917 dual amplifi-
er features separate shutdown inputs. Shut down both
amplifiers for lowest quiescent current.
Power-Supply Bypassing and Layout
Bypass VDD with a 0.1F capacitor to ground as close
to the pin as possible to minimize noise.
Good layout techniques optimize performance by
decreasing the amount of stray capacitance and induc-
tance to the op amp’s inputs and outputs. Minimize
stray capacitance and inductance, by placing external
components close to the IC.
Figure 1. Rail-to-Rail Output Voltage Range
RAIL-TO-RAIL OUTPUT VOLTAGE RANGE
200
μs/div
3V
0V
3V
0V
IN_
1V/div
OUT_
1V/div
VDD = 3V
Figure 2. Using a Resistor to Isolate a Capacitive Load from
the Op Amp
MAX9914–
MAX9917
RISO
CL
RL
AV =
≈ 1V/V
RL
RL + RISO
Figure 3. Power-Up Test Configuration
MAX991_
100k
Ω
100k
Ω
OUT
IN-
IN+
0V
5.5V
VDD
VSS
相關PDF資料
PDF描述
TSW-124-08-L-D CONN HEADER 48POS .100" DL GOLD
91596-108 91596-108-LPVCC B.E SMT
TSW-140-05-G-S CONN HEADER 40POS .100" SGL GOLD
929710-10-35-RK CONN HEADER .100 DUAL STR 70POS
91596-122 91596-122-LPVCC B.E SMT
相關代理商/技術參數
參數描述
MAX9915EXT 制造商:Maxim Integrated Products 功能描述:1MHZ 20+A RAIL-TO-RAIL I/O OP AMP - Cut Tape Product
MAX9915EXT+ 制造商:Maxim Integrated Products 功能描述:OP AMP SGL GP R-R I/O 5.5V 6PIN SC-70 - Rail/Tube
MAX9915EXT+T 功能描述:運算放大器 - 運放 1MHz 4uA Rail-Rail Op Amp RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比(最小值):63 dB 輸入補償電壓:1 mV 輸入偏流(最大值):10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel
MAX9915EXT-T 功能描述:運算放大器 - 運放 1MHz 4uA Rail-Rail Op Amp RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比(最小值):63 dB 輸入補償電壓:1 mV 輸入偏流(最大值):10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel
MAX9916EKA 制造商:Maxim Integrated Products 功能描述:1MHZ 20UA R2R I/O OP AMP DUAL W - Cut Tape Product