- 您現在的位置：買賣IC網 > PDF目錄2092 > MAX9796EBX+TG45 (Maxim Integrated Products)IC AMP AUDIO 2.3W MONO D 36UCSP PDF資料下載
參數資料
| 型號： | MAX9796EBX+TG45 |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 13/28頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC AMP AUDIO 2.3W MONO D 36UCSP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 2,500 |
| 系列： | DirectDrive® |
| 類型： | D 類 |
| 輸出類型： | 1-通道（單聲道），帶立體聲耳機 |
| 在某負載時最大輸出功率 x 通道數量： | 2.3W x 1 @ 4 歐姆 |
| 電源電壓： | 2.7 V ~ 5.5 V |
| 特點： | 消除爆音，差分輸入，I²C，靜音，短路和熱保護，關機，音量控制 |
| 安裝類型： | 表面貼裝 |
| 供應商設備封裝： | 36-UCSP |
| 封裝/外殼： | 36-WFBGA，CSBGA |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
MAX9796
Early STOP Conditions
The MAX9796 recognizes a STOP condition at any point
during data transmission except if the STOP condition
occurs in the same high pulse as a START condition.
Slave Address
The MAX9796 is available with one preset slave
address (see Table 1). The address is defined as the
seven most significant bits (MSBs) followed by the
read/write (R/W) bit. The address is the first byte of
information sent to the MAX9796 after the START condi-
tion. The MAX9796 is a slave device only capable of
being written to. The R/W bit should be a zero when
configuring the MAX9796.
Acknowledge
The acknowledge bit (ACK) is a clocked 9th bit that the
MAX9796 uses to handshake receipt of each byte of
data (see Figure 9). The MAX9796 pulls down SDA dur-
ing the master-generated 9th clock pulse. Monitoring
ACK allows for detection of unsuccessful data transfers.
An unsuccessful data transfer occurs if a receiving
device is busy or if a system fault has occurred. In the
event of an unsuccessful data transfer, the bus master
may reattempt communications.
Write Data Format
A write to the MAX9796 includes transmission of a
START condition, the slave address with the R/W bit set
to 0 (Table 1), one byte of data to configure the
Command Register, and a STOP condition. Figure 10
illustrates the proper format for one frame.
The MAX9796 only accepts write data, but it acknowl-
edges the receipt of the address byte with the R/W bit
set high. The MAX9796 does not write to the SDA bus
in the event that the R/W bit is set high. Subsequently,
the master reads all 1’s from the MAX9796. Always set
the R/W bit to zero to avoid this situation.
Programming the MAX9796
The MAX9796 is programmed through six control regis-
ters. Each register is addressed by the three MSBs
(B5–B7) followed by five configure bits (B0–B4) as
shown in Table 2. Correct programming of the MAX9796
requires writing to all six control registers. Upon power-
on, their default settings are as listed in Table 3.
2.3W, High-Power Class D Audio Subsystem
with DirectDrive Headphone Amplifiers
20
______________________________________________________________________________________
1
SCL
START
CONDITION
SDA
28
9
CLOCK PULSE FOR
ACKNOWLEDGMENT
ACKNOWLEDGE
NOT ACKNOWLEDGE
SLAVE ADDRESS
A6
A5
A4
A3
A2
A1
A0
R/
W
100
11010
Figure 9. Acknowledge
S
ACK
0
ACKNOWLEDGE FROM MAX9796
R/W
ACKNOWLEDGE
FROM MAX9796
B7 B6 B5 B4 B3 B2
COMMAND BYTE IS STORED ON
RECEIPT OF STOP CONDITION
ACK
P
B1 B0
SLAVE ADDRESS
COMMAND BYTE
Figure 10. Write Data Format Example
Table 1. MAX9796 Address Map
B7
B6
B5
B4
B3
B2
B1
B0
FUNCTION
COMMAND
DATA
Input Mode Control
0
INMODE (Tables 5a and 5b)
Mono Volume Control
0
1
MVOL (Table 7)
Left Volume Control
0
1
0
LVOL (Table 7)
Right Volume Control
0
1
RVOL (Table 7)
Output Mode Control
1
0
MONO+6dB
OUTMODE (Table 9)
Global Control Register
1
0
1
SHDN
IN+6dB
MUTE
SSM
MONO
Table 2. Control Registers
相關PDF資料 |
PDF描述 |
|---|---|
| MAX9813LEKA+T | IC AMP AUDIO MONO AB MIC SOT23-8 |
| MAX9814ETD+T | IC AMP AUDIO MONO AB MIC 14TDFN |
| MAX9820ETB+T | IC AMP AUD HDPHE 95MW 10TDFN |
| MAX98300SETA+T | IC AMP AUD SPKR 2W MONO D 8TDFN |
| MAX98302ETD+ | IC AMP STER CLASS D 2.4W 14TDFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX9796EVKIT | 制造商:Maxim Integrated Products 功能描述:2.3W HIGH-POWER CLASS D AUDIO SUBS - Rail/Tube |
| MAX9796EVKIT+ | 制造商:Maxim Integrated Products 功能描述:MAX9796 EVAL KIT - Boxed Product (Development Kits) |
| MAX98088EVKIT# | 功能描述:音頻 IC 開發工具 MAX98088 Eval Kit RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V |
| MAX98088EVKIT+ | 功能描述:音頻 IC 開發工具 MAX98088 Eval Kit RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V |
| MAX98088EWY+T | 功能描述:接口—CODEC Dual I2S Codec RoHS:否 制造商:Texas Instruments 類型: 分辨率: 轉換速率:48 kSPs 接口類型:I2C ADC 數量:2 DAC 數量:4 工作電源電壓:1.8 V, 2.1 V, 2.3 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-81 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。