- 您現在的位置：買賣IC網 > PDF目錄384715 > MAX9759 (Maxim Integrated Products, Inc.) 3.2W, High-Efficiency, Low-EMI, Filterless, Class D Audio Amplifier PDF資料下載
參數資料
| 型號： | MAX9759 |
| 廠商： | Maxim Integrated Products, Inc. |
| 元件分類： | 運動控制電子 |
| 英文描述： | 3.2W, High-Efficiency, Low-EMI, Filterless, Class D Audio Amplifier |
| 中文描述： | 3.2W、高效、低EMI、無需濾波、D類音頻放大器 |
| 文件頁數： | 14/20頁 |
| 文件大小： | 957K |
| 代理商： | MAX9759 |
Mute
The MAX9759 features a mute function that disables
the H-bridge outputs of the switching amplifier. The
mute function only affects the power amplifiers of the
MAX9759; it does not shut down the device. Driving
MUTE
low places the MAX9759 in a disabled output
mode. Drive
MUTE
high for normal operation.
Click-and-Pop Suppression
The MAX9759 features comprehensive click-and-pop
suppression that eliminates audible transients on startup
and shutdown. While in shutdown, the H-bridge is in a
high-impedance state. During startup or power-up, the
input amplifiers are muted and an internal loop sets the
modulator bias voltages to the correct levels, preventing
clicks and pops when the H-bridge is subsequently
enabled. For 40ms following startup, a soft-start function
gradually unmutes the input amplifiers.
For improved click-and-pop performance, sequence the
digital inputs of the
SHDN
and
MUTE
pins of the
MAX9759 during power-up and power-down of the
device such that transients are eliminated from each
power cycle. Apply power to the MAX9759 with both
SHDN
and
MUTE
held low. Release
SHDN
before
MUTE
such that minimal transients occur during startup of the
device. The mute function allows the MAX9759 to be
powered up with the H-bridge outputs of the switching
amplifier disabled. For power-down, sequence the power
cycle such that the amplifier is muted first and subse-
quently shut down before power is disconnected from the
IC. This power cycle eliminates any audible transients on
power-up and power-down of the MAX9759.
Applications Information
Filterless Operation
Traditional class D amplifiers require an output filter to
recover the audio signal from the amplifier’s output. The
filters add cost, increase the solution size of the amplifi-
er, and can decrease efficiency. The traditional PWM
scheme uses large differential output swings (2 x V
DD
peak-to-peak) and causes large ripple currents. Any
parasitic resistance in the filter components results in a
loss of power, lowering the efficiency.
The MAX9759 does not require an output filter for the short
speaker cable. The device relies on the inherent induc-
tance of the speaker coil and the natural filtering of both
the speaker and the human ear to recover the audio com-
ponent of the square-wave output. Eliminating the output
filter results in a smaller, less costly, more efficient solution.
Because the frequency of the MAX9759 output is well
beyond the bandwidth of most speakers, voice coil
movement due to the switching frequency is very small.
Although this movement is small, a speaker not
designed to handle the additional power can be dam-
aged. For optimum results, use a speaker with a series
inductance > 10μH to 100μH range.
Power-Conversion Efficiency
Unlike a class AB amplifier, the output offset voltage of a
class D amplifier does not noticeably increase quiescent
current draw when a load is applied. This is due to the
power conversion of the class D amplifier. For example,
an 8mV DC offset across an 8
load results in 1mA extra
current consumption in a class AB device. In the class D
case, an 8mV offset into an 8
load equates to an addi-
tional power drain of 8μW. Due to the high efficiency of
the class D amplifier, this represents an additional quies-
cent current draw of 8μW/(V
DD
/100
η
), which is on the
order of a few microamps.
Input Amplifier
Differential Input
The MAX9759 features a differential input structure,
making it compatible with many CODECs, and offers
improved noise immunity over a single-ended input
amplifier. High-frequency signals can be picked up by
the amplifier’s input traces and can appear at the
amplifier’s inputs as common-mode noise. A differential
input amplifier amplifies the difference of the two
inputs; any signal common to both inputs is cancelled.
Single-Ended Input
The MAX9759 can be configured as a single-ended input
amplifier by capacitively coupling one input to GND while
simultaneously driving the other input (Figure 6).
DC-Coupled Input
The input amplifier can accept DC-coupled inputs that
are biased within the amplifier’s common-mode range
(see the
Typical Operating Characteristics
). DC coupling
eliminates the input-coupling capacitors, reducing com-
ponent count to potentially one external component (see
the
System Diagram
). However, the low-frequency rejec-
tion of the capacitors is lost, allowing low-frequency sig-
nals to feedthrough to the load.
M
3.2W, High-Efficiency, Low-EMI, Filterless,
Class D Audio Amplifier
14
______________________________________________________________________________________
1
μ
F
IN+
IN-
1
μ
F
SINGLE-ENDED
AUDIO INPUT
MAX9759
Figure 6. Single-Ended Input
相關PDF資料 |
PDF描述 |
|---|---|
| MAX975ESA | Octal Transparent D-type Latches With 3-State Outputs 20-LCCC -55 to 125 |
| MAX975-MAX977 | Single/Dual, +3V/+5V Dual-Speed Comparators with Auto-Standby |
| MAX977 | Octal Edge-Triggered D-type Flip-Flops With 3-State Outputs 20-LCCC -55 to 125 |
| MAX977EEE | Octal Edge-Triggered D-type Flip-Flops With 3-State Outputs 20-CFP -55 to 125 |
| MAX977ESD | Single/Dual, +3V/+5V Dual-Speed Comparators with Auto-Standby |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX9759ETE+ | 功能描述:音頻放大器 3.2W Low-EMI Class D Amplifier RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| MAX9759ETE+T | 功能描述:音頻放大器 3.2W Low-EMI Class D Amplifier RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| MAX9759EUE+ | 制造商:Maxim Integrated Products 功能描述:- Rail/Tube |
| MAX9759EUE+T | 制造商:Maxim Integrated Products 功能描述:AUD AMP SPKR 1CH MONO 4.3W CLS-D 16TSSOP - Tape and Reel |
| MAX9759EVKIT | 功能描述:音頻放大器 Evaluation Kit for the MAX9759 RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。