- 您現在的位置：買賣IC網 > PDF目錄1946 > MAX9621AUB+T (Maxim Integrated Products)IC HALL EFFECT SENSOR 10UMAX PDF資料下載
參數資料
| 型號： | MAX9621AUB+T |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 3/15頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC HALL EFFECT SENSOR 10UMAX |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 2,500 |
| 類型： | 霍爾效應傳感器 |
| 輸入類型： | 邏輯 |
| 輸出類型： | 模擬，數字 |
| 接口： | 2 線 |
| 電流 - 電源： | 1mA |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 10-TFSOP，10-MSOP（0.118"，3.00mm 寬） |
| 供應商設備封裝： | 10-µMAX |
| 包裝： | 帶卷 (TR) |
11
Maxim Integrated
Dual, 2-Wire Hall-Effect Sensor Interface with
Analog and Digital Outputs
MAX9621
Sleep Mode Input (SLEEP)
The MAX9621 features an active-low SLEEP input. Pull
SLEEP low for more than 40Fs to put the device into
sleep mode for power saving. In sleep mode, the DOUT1
and DOUT2 outputs are high impedance and are pulled
high by pullup resistors. AOUT1 and AOUT2 are set to
zero-output current.
Hall Input Restart
When an input has been shut down due to a short to
ground, cycle SLEEP for 10Fs to 20Fs to restart the input.
If the other input is operational it is not affected. The
restart happens on the rising edge of SLEEP.
Input Current Thresholds and
Short to Ground
The input current high and low thresholds that determine
the logic level of the digital outputs are adjusted by
changing the RSET value. When the RSET value changes,
the following parameters change as well: IIN_HYS, ISC,
tBL, tRAMP, tDEL, fMAX, and PR.
IIH, IIL, IIN_HYS, ISC, tRAMP, and fMAX are inversely pro-
portional to RSET and decrease as RSET increases. This
inverse relationship is linear. For example, a 10% change in
(1/RSET) results in a 10% change in current parameters.
Conversely, time and delay parameters are linear and
directly proportional to RSET, and a 10% change in RSET
results in an 10% change in time parameters.
The difference between the maximum and minimum
threshold current limits is the min/max limit spread, which
is greater than the threshold hysteresis. The min/max
spread and the hysteresis both change by the same per-
centage as the mean of the threshold current limits. The
following equation is useful for finding the mean of the
threshold current limits given a value of RSET resistance:
(
)
0
1
II
I 0
Rm
=
+<
×
I is the mean of the threshold current limits, R is
the value of the RSET resistance in kΩ, the constant
I0 = 0.03717mA, and the constant m = -0.001668
(1/(kΩ x mA)).
The following equation is useful for finding the value of
RSET resistance given a mean of the threshold current
limits:
(
)
0
Y Y
m II 0
1
R
Y
=
+
×
<
=
Y0 = 6.2013 x 10-5 units of (1/kΩ)
To compute the typical input current thresholds from the
mean input current, it is necessary to obtain the hyster-
esis. The following equation finds the hysteresis given
the mean threshold current, I:
H = H0 + k x I (I < 0)
where H0 = -0.033463 in mA, and k = -0.08414 in mA/mA.
Input current threshold high = I - H/2, input current
threshold low = I + H/2.
Application Information
Use of Digital and Analog Outputs
The digital output can be used to provide the FP with an
interrupt signal that can represent a Hall sensor change
of status. DOUT1 and DOUT2 provide a time domain
output filter for robust noise immunity. See Figure 2.
The analog output can be connected to an ADC with an
appropriate load resistor, and can be used to perform
custom diagnostics.
Figure 4. Hall Input Reenergized When Open Input Is Reconnected to Hall Sensor
14V
VIN_
8V
5mA/
s
HALL INPUT RECONNECTED
TO HALL SENSOR
11.5mA
IIN_
0V
0A
TIME
VBAT - 500mV
VBAT - 25mV
相關PDF資料 |
PDF描述 |
|---|---|
| MAX9655AEE+ | IC SW VIDEO LOW POWER 16-QSOP |
| MAX9671CTH+T | IC AUDIO/VIDEO SWIT DUAL 44TQFN |
| MAX9675ECQ+ | IC CROSSPOINT SWIT 16X16 100TQFP |
| MAX9921AUB/V+T | IC HALL EFFECT SENSOR DL 10UMAX |
| MAX9925AUB+ | IC SENSOR INTERFACE VARI 10MSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX9621EVKIT+ | 功能描述:板機接口霍耳效應/磁性傳感器 Hall Sensor Interface RoHS:否 制造商:Honeywell 類型:Bipolar Hall-Effect Digital Position Sensor 工作電源電壓:3 V to 24 V 電源電流:3.5 mA 最大輸出電流:20 mA 工作點最小值/最大值:5 G, 55 G 最小/最大釋放點（Brp）:- 55 G, - 5 G 最大工作溫度:+ 150 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-23 |
| MAX9622AXK+ | 制造商:Maxim Integrated Products 功能描述:SINGLE/DUAL HIGH-BANDWIDTH OPAMPS IN SC7 - Rail/Tube |
| MAX9622AXK+T | 功能描述:運算放大器 - 運放 High-Bandwidth Op Amp RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
| MAX9622EVKIT+ | 功能描述:放大器 IC 開發工具 MAX9622 Eval Kit RoHS:否 制造商:International Rectifier 產品:Demonstration Boards 類型:Power Amplifiers 工具用于評估:IR4302 工作電源電壓:13 V to 23 V |
| MAX9623AXK+T | 功能描述:運算放大器 - 運放 High-Bandwidth Op Amp RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。