參數資料
型號: MAX9507ATE+
廠商: Maxim Integrated Products
文件頁數: 8/29頁
文件大?。?/td> 0K
描述: IC DIRECTDRIVE FILTER AMP 16TQFN
產品培訓模塊: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝: 100
系列: DirectDrive®
應用: 濾波器
電路數: 1
-3db帶寬: 40.7MHz
轉換速率: 35 V/µs
電流 - 電源: 3.1mA
電流 - 輸出 / 通道: 82mA
電壓 - 電源,單路/雙路(±): 1.7 V ~ 2.63 V
安裝類型: 表面貼裝
封裝/外殼: 16-WFQFN 裸露焊盤
供應商設備封裝: 16-TQFN-EP(3x3)
包裝: 管件
配用: MAX9507EVKIT+-ND - KIT EVAL FOR MAX9508
MAX9507EVCMAXQU+-ND - SYSTEM EVAL FOR MAX9507 KIT+MOD
MAX9507
1.8V DirectDrive Video Filter Amplifier with
Load Detection and Dual SPST Analog Switches
16
______________________________________________________________________________________
I2C Serial Interface
The MAX9507 features an I2C/SMBus-compatible, 2-
wire serial interface consisting of a serial-data line (SDA)
and a serial-clock line (SCL). SDA and SCL facilitate
communication between the MAX9507 and the master at
clock rates up to 400kHz. Figure 3 shows the 2-wire inter-
face timing diagram. The master generates SCL and initi-
ates data transfer on the bus. A master device writes data
to the MAX9507 by transmitting a START (S) condition,
the proper slave address with the R/W bit set to 0, fol-
lowed by the register address and then the data word.
Each transmit sequence is framed by a START and a
STOP (P) condition. Each word transmitted to the
MAX9507 is 8 bits long and is followed by an acknowl-
edge clock pulse. A master reads from the MAX9507 by
transmitting the slave address with the R/W bit set to 0,
the register address of the register to be read, a REPEAT-
ED START (Sr) condition, the slave address with the R/W
bit set to 1, followed by a series of SCL pulses. The
MAX9507 transmits data on SDA in sync with the master-
generated SCL pulses. The master acknowledges receipt
of each byte of data. Each read sequence is framed by a
START or REPEATED START condition, an acknowledge
or a not acknowledge, and a STOP condition. SDA oper-
ates as both an input and an open-drain output. A pullup
resistor, typically greater than 500
Ω, is required on the
SDA bus. SCL operates as only an input. A pullup resis-
tor, typically greater than 500
Ω, is required on SCL if
there are multiple masters on the bus, or if the master in a
single-master system has an open-drain SCL output.
Table 2. Configuration Register (0x00)
BIT
NAME
FUNCTION
B7
SW2EN
1 = Analog switch 2 closed.
0 = Analog switch 2 open.
B6
SW1EN
1 = Analog switch 1 closed.
0 = Analog switch 1 open.
B4
STEN
1 = Transparent sync-tip clamp enabled, the input can be DC- or AC-coupled.
0 = Transparent sync-tip clamp disabled, the input must be DC-coupled.
B3
FLTEN
1 = Video filter enabled.
0 = Video filter disabled (bypassed).
B1
SPEN
1 = Signal path enabled* (SPEN overrides the ASPEN setting).
0 = Signal path disabled.
B0
CPEN
1 = Charge pump enabled (CPEN overrides the ACPEN setting).
0 = Charge pump disabled.
*
Internal control circuitry prevents the signal path from turning on until the charge pump has been enabled and has settled.
Table 3. Video Load-Detect Register (0x01)
BIT
NAME
FUNCTION
B7
LOAD*
1 = Load detected.
0 = No load detected.
B3
LCFEN
1 = Changes to the video load will trigger LCF to pull low.
0 = Changes to the video load are not reported.
B1
ASPEN
1 = Enable automatic control of the video signal path**.
0 = Disable automatic control of the video signal path.
B0
ACPEN
1 = Enable automatic control of the charge pump***.
0 = Disable automatic control of the charge pump.
*
Read-only bit indicating the load status when the video load-detect circuitry is enabled (ASPEN = 1 or ACPEN = 1). When LCFEN = 1,
reading this bit will clear the LCF flag.
**
If SPEN = 0, then the signal path will be automatically enabled when a video load is detected and the charge pump has been
enabled and has settled.
***
If CPEN = 0, then the charge pump will be automatically enabled when a video load is detected.
SMBus is a trademark of Intel Corp.
相關PDF資料
PDF描述
AD7549JP IC DAC 12BIT DUAL LC2MOS 20-PLCC
MAX9650AUA+ IC OP AMP VCOM DRIVE 8-UMAX-EP
AD561JNZ IC DAC 10BIT MONO VOLT IN 16DIP
AD7841ASZ-REEL IC DAC 14BIT OCTAL VOUT 44-MQFP
VE-J1X-MZ-B1 CONVERTER MINIMOD DC/DC 5.2V 25W
相關代理商/技術參數
參數描述
MAX9507ATE+ 功能描述:視頻放大器 1.8V DirectDrive Video Filter Amp RoHS:否 制造商:ON Semiconductor 通道數量:4 電源類型: 工作電源電壓:3.3 V, 5 V 電源電流: 最小工作溫度: 最大工作溫度: 封裝 / 箱體:TSSOP-14 封裝:Reel
MAX9507ATE+T 功能描述:視頻放大器 1.8V DirectDrive Video Filter Amp RoHS:否 制造商:ON Semiconductor 通道數量:4 電源類型: 工作電源電壓:3.3 V, 5 V 電源電流: 最小工作溫度: 最大工作溫度: 封裝 / 箱體:TSSOP-14 封裝:Reel
MAX9507EVCMAXQU+ 功能描述:放大器 IC 開發工具 MAX9507 Eval Kit RoHS:否 制造商:International Rectifier 產品:Demonstration Boards 類型:Power Amplifiers 工具用于評估:IR4302 工作電源電壓:13 V to 23 V
MAX9507EVKIT 功能描述:視頻放大器 RoHS:否 制造商:ON Semiconductor 通道數量:4 電源類型: 工作電源電壓:3.3 V, 5 V 電源電流: 最小工作溫度: 最大工作溫度: 封裝 / 箱體:TSSOP-14 封裝:Reel
MAX9507EVKIT+ 功能描述:放大器 IC 開發工具 MAX9507 Eval Kit RoHS:否 制造商:International Rectifier 產品:Demonstration Boards 類型:Power Amplifiers 工具用于評估:IR4302 工作電源電壓:13 V to 23 V