- 您現在的位置：買賣IC網 > PDF目錄385556 > MAX9507 (Maxim Integrated Products, Inc.) 1.8V DirectDrive Video Filter Amplifier with Load Detection and Dual SPST Analog Switches PDF資料下載
參數資料
| 型號： | MAX9507 |
| 廠商： | Maxim Integrated Products, Inc. |
| 英文描述： | 1.8V DirectDrive Video Filter Amplifier with Load Detection and Dual SPST Analog Switches |
| 中文描述： | 1.8V、DirectDrive視頻濾波放大器，提供負載檢測和兩路SPST模擬開關 |
| 文件頁數： | 12/29頁 |
| 文件大小： | 480K |
| 代理商： | MAX9507 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁當前第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁
M
1.8V DirectDrive Video Filter Amplifier with
Load Detection and Dual SPST Analog Switches
12
______________________________________________________________________________________
Pin Description
PIN
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
—
NAME
IN
SDA
SCL
DEV_ADDR
V
DD
C1P
CPGND
C1N
V
SS
OUT
GND
LCF
NO1
COM1
COM2
NO2
EP
FUNCTION
Video Input
I
2
C-Compatible Serial-Data Input/Output
I
2
C-Compatible Serial-Clock Input
I
2
C Device Address Input. Connect DEV_ADDR to GND, V
DD
, SCL, or SDA. See Table 4.
Positive Power Supply. Bypass with a 0.1μF capacitor to GND.
Charge-Pump Flying Capacitor Positive Terminal. Connect a 1μF capacitor from C1P to C1N.
Charge-Pump Ground
Charge-Pump Flying Capacitor Negative Terminal. Connect a 1μF capacitor from C1P to C1N.
Charge-Pump Negative Power Supply. Bypass with a 1μF capacitor to GND.
Video Output
Ground
Load Change Flag. Open-drain, active-low signal indicates when a video load change occurs.
Normally Open Terminal 1
Common Terminal 1
Common Terminal 2
Normally Open Terminal 2
Exposed Pad. EP is internally connected to GND. Connect EP to GND.
Detailed Description
The MAX9507 represents Maxim’s second-generation
of DirectDrive video amplifiers that meet the require-
ments of current and future portable equipment:
1.8V Operation: Eliminate the need for 3.3V supply in
favor of lower supply voltages.
Lower Power Consumption: The MAX9507 reduces
average power consumption by up to 75% com-
pared to the 3.3V first generation (MAX9503/
MAX9505).
Internal Fixed Gain of 8: As the supply voltages drop
for system chips on deep submicron processes, the
video DAC can no longer create a 1V
P-P
signal at its
output, and the gain of 2 found in the previous gen-
eration of video filter amplifiers is not enough.
Load Reporting: The MAX9507 senses the presence
of a video load. For portable devices, a video load is
not connected most of the time, and turning off the
video encoder saves power. Another benefit of load
reporting is a simpler user interface, eliminating the
need to browse through menus to activate the video
output. Instead, the equipment will automatically
enable this feature.
Dual SPST Analog Switches: The two analog switch-
es are ideal for routing additional audio, video, or
digital signals.
DirectDrive technology is necessary for a voltage-mode
amplifier to output a 2V
P-P
video signal from a 1.8V
supply. The integrated inverting charge pump creates
a negative supply that increases the output range and
gives the video amplifier enough headroom to drive a
2V
P-P
video signal into a 150
Ω
load.
DirectDrive
Background
Integrated video filter amplifier circuits operate from a
single supply. The positive power supply usually cre-
ates video output signals that are level-shifted above
ground to keep the signal within the linear range of the
output amplifier. For applications where the positive DC
level is not acceptable, a series capacitor can be
inserted in the output connection in an attempt to elimi-
nate the positive DC level shift. The series capacitor
cannot truly level shift a video signal because the aver-
age level of the video varies with picture content. The
series capacitor biases the video output signal around
ground, but the actual level of the video signal can vary
significantly depending upon the RC time constant and
the picture content.
相關PDF資料 |
PDF描述 |
|---|---|
| MAX9508 | Video Filter Amplifier with SmartSleep and Bidirectional Video Support |
| MAX9508AEE | Video Filter Amplifier with SmartSleep and Bidirectional Video Support |
| MAX9508ATE | Video Filter Amplifier with SmartSleep and Bidirectional Video Support |
| MAX951-MAX954 | Ultra Low Power Single-Supply Op Amp + Comparator + Reference |
| MAX9511_07 | RGBHV Driver with EMI Suppression |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX9507ATE+ | 功能描述:視頻放大器 1.8V DirectDrive Video Filter Amp RoHS:否 制造商:ON Semiconductor 通道數量:4 電源類型: 工作電源電壓:3.3 V, 5 V 電源電流: 最小工作溫度: 最大工作溫度: 封裝 / 箱體:TSSOP-14 封裝:Reel |
| MAX9507ATE+T | 功能描述:視頻放大器 1.8V DirectDrive Video Filter Amp RoHS:否 制造商:ON Semiconductor 通道數量:4 電源類型: 工作電源電壓:3.3 V, 5 V 電源電流: 最小工作溫度: 最大工作溫度: 封裝 / 箱體:TSSOP-14 封裝:Reel |
| MAX9507EVCMAXQU+ | 功能描述:放大器 IC 開發工具 MAX9507 Eval Kit RoHS:否 制造商:International Rectifier 產品:Demonstration Boards 類型:Power Amplifiers 工具用于評估:IR4302 工作電源電壓:13 V to 23 V |
| MAX9507EVKIT | 功能描述:視頻放大器 RoHS:否 制造商:ON Semiconductor 通道數量:4 電源類型: 工作電源電壓:3.3 V, 5 V 電源電流: 最小工作溫度: 最大工作溫度: 封裝 / 箱體:TSSOP-14 封裝:Reel |
| MAX9507EVKIT+ | 功能描述:放大器 IC 開發工具 MAX9507 Eval Kit RoHS:否 制造商:International Rectifier 產品:Demonstration Boards 類型:Power Amplifiers 工具用于評估:IR4302 工作電源電壓:13 V to 23 V |
發布緊急采購，3分鐘左右您將得到回復。