- 您現在的位置：買賣IC網 > PDF目錄385556 > MAX9483CEE (MAXIM INTEGRATED PRODUCTS INC) Dual-Output, Multimode CD-RW/DVD Laser-Diode Drivers PDF資料下載
M
Dual-Output, Multimode
CD-RW/DVD Laser-Diode Drivers
_______________________________________________________________________________________
7
ENABLE
NE2
NE3
t
EN
t
ON
t
ON
t
OFF
t
OFF
t
DIS
t
r
t
r
t
f
t
f
I
OUT
H
L
H
L
H
L
TIME
Figure 1. Timing Diagram of Output vs. Control Signals
Detailed Description
Read Channel and Write Channels
The MAX9483/MAX9484 high-performance multimode
LDDs are designed for CD and DVD combination pick-
up heads. The drivers have three current channels.
Each channel has a current input IN_ (_ = 1, 2, or 3)
and a channel control signal (ENABLE, NE2, or NE3).
IN1 supplies the reference for the read channel, which
provides the read current or the offset current to the
lasers. The other two channels are the write channels.
The currents of these two channels are superimposed
on the read current that serves as the offset current for
the laser in write mode. The offset current significantly
reduces the laser output ramp-up time. When ENABLE
is low, all three channels are disabled. Driving ENABLE
high enables the read channel and leaves the other two
write channels to be controlled by NE2 and NE3 (see
Figure 1). By selecting the input currents at IN2 and
IN3, as well as the signal timing of NE2 and NE3, the
drivers can generate various current waveforms for dif-
ferent CD/DVD writing standards. All three channels
have a current gain of 100. The maximum total current
each output can provide is 400mA.
RF Oscillator
To reduce the laser-mode hopping noise in read mode,
modulate the read current with an oscillator with a
100MHz to 600MHz frequency. An external resistor, RF,
determines the oscillator frequency selection. For the
MAX9484, two external resistors, R
F1
and R
F2
, are
used to select the oscillator frequency for CD and DVD
lasers separately. The swing amplitude of the oscillator
current is set by two external resistors, R
S1
and R
S2
,
one for CD and one for DVD. The oscillator is enabled
when both ENABLE and ENOSC are driven high.
相關PDF資料 |
PDF描述 |
|---|---|
| MAX9483CTE | Dual-Output, Multimode CD-RW/DVD Laser-Diode Drivers |
| MAX9484CTP | Dual-Output, Multimode CD-RW/DVD Laser-Diode Drivers |
| MAX9489 | Multiple-Output Network Clock Generator |
| MAX9489ETJ | Multiple-Output Network Clock Generator |
| MAX9491ETP | Factory-Programmable, Single PLL Clock Generator |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX9483CEE+T | 功能描述:激光驅動器 RoHS:否 制造商:Micrel 數據速率:4.25 Gbps 工作電源電壓:3 V to 3.6 V 電源電流:80 mA 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-16 封裝:Tube |
| MAX9483CEE-T | 功能描述:激光驅動器 RoHS:否 制造商:Micrel 數據速率:4.25 Gbps 工作電源電壓:3 V to 3.6 V 電源電流:80 mA 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-16 封裝:Tube |
| MAX9483EEE | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| MAX9484CTP | 功能描述:激光驅動器 RoHS:否 制造商:Micrel 數據速率:4.25 Gbps 工作電源電壓:3 V to 3.6 V 電源電流:80 mA 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-16 封裝:Tube |
| MAX9484CTP-T | 功能描述:激光驅動器 RoHS:否 制造商:Micrel 數據速率:4.25 Gbps 工作電源電壓:3 V to 3.6 V 電源電流:80 mA 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-16 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。