- 您現在的位置：買賣IC網 > PDF目錄16166 > MAX9406EVKIT+ (Maxim Integrated Products)KIT EVAL FOR MAX9406 PDF資料下載
參數資料
| 型號： | MAX9406EVKIT+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 8/11頁 |
| 文件大小： | 0K |
| 描述： | KIT EVAL FOR MAX9406 |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 1 |
| 主要目的： | 視頻，視頻處理 |
| 嵌入式： | 否 |
| 已用 IC / 零件： | MAX9406 |
| 主要屬性： | DisplayPort? 至 DVI?/HDMI? 電平位移器 |
| 次要屬性： | 2Gbps 數據速率 |
| 已供物品： | 板 |
MAX9406
DisplayPort to DVI/HDMI Level Shifter
6
_______________________________________________________________________________________
Detailed Description
The MAX9406 high-speed, low-skew, quad differential
input to CML translator is designed for high-speed sig-
nal conversion of the DP to HDMI technology. This
device features ultra-low propagation delay of 350ps
and channel-to-channel skew of less than 20ps. The
MAX9406 supports typical data rates of 2Gbps.
The MAX9406 provides the level shift for HDMI’s DDC
and HPD, which converts the 5V single-ended logic to
3.3V single-ended logic.
High-Speed Signal Enables
OE controls the power through the entire length of the
four high-speed signal paths. Setting
OE low enables
all of the high-speed signal paths. Setting
OE high dis-
ables all high-speed links and disconnects the internal
biasing supply and brings the device to the low-power
state. In the low-power state, however, the DDC and
HPD ports are still functioning.
Display Data Channel (DDC)
The MAX9406 allows the translation between 5V and 3V
of the lower speed DDC lines. Whenever one side is
pulled to GND, the other side follows and vice versa.
DDC_EN controls the gating to the DDC link. Setting
DDC_EN high enables data to pass through the DDC,
while setting DDC_EN low disables the DDC link.
Hot-Plug Detection (HPD)
The MAX9406 translates the HPD 5V logic into 3V logic.
Applications Information
DVI/HDMI Driver
The MAX9406 can be used as the driver for the HDMI
signal on the motherboard. The MAX9406 CML output
provides a > 400mV differential HDMI output and sup-
ports 3.3V pullup at the differential outputs. The level
shifter boosts the differential signal from the graphics
chip to the HDMI connector, located on the edge of the
motherboard.
High-Speed Signal Line Enable/Disable
The MAX9406 allows use of the DDC lines independent
of the state of the high-speed signal lines and the
OE
pin. This allows communication through DDC without
any high-speed signals.
Output Termination
Terminate CML outputs through 50
Ω to VCC or use an
equivalent Thevinin termination. Terminate both outputs
and use identical terminations on each for the lowest
output-to-output skew.
Power-Supply Bypassing
Adequate power-supply bypassing is necessary to
maximize the performance and noise immunity. Bypass
VCC to GND with high-frequency surface-mount 0.01F
ceramic capacitors as close to the device as possible.
Use multiple bypass vias for connection to minimize
inductance.
Functional Diagram
MAX9406
IN_D1-
IN_D1+
OUT_D1-
OUT_D1+
VT
50
Ω
x2
IN_D2-
IN_D2+
OUT_D2-
OUT_D2+
VT
50
Ω
x2
IN_D3-
IN_D3+
OUT_D3-
OUT_D3+
VT
50
Ω
x2
IN_D4-
IN_D4+
OUT_D4-
OUT_D4+
SDA_SRC
SCK_SRC
SDA_SNK
SCK_SNK
VT
50
Ω
x2
DDC LEVEL SHIFTER
HPD BUFFER
HPD_SRC
HPD_SNK
60k
Ω
VCC
GND
OE
DDC_EN
相關PDF資料 |
PDF描述 |
|---|---|
| 10018960-P0100AULF | CABLE ASSY EYEMAX 4X 1M W/SCREWS |
| M1AXA-6040K | IDC CABLE - MSC60A/MC60F/X |
| SPD125R-473M | INDUCTOR PWR SHIELDED 47UH SMD |
| M1CXA-6040K | IDC CABLE - MKC60A/MC60G/X |
| MCP73842T-840I/UN | IC CONTROLLER LI-ION 8.4V 10MSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX9406EVKIT+ | 功能描述:視頻 IC MAX9406 Eval Kit RoHS:否 制造商:Fairchild Semiconductor 工作電源電壓:5 V 電源電流:80 mA 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-28 封裝:Reel |
| MAX941AUA+T | 制造商:Maxim Integrated Products 功能描述:COMPARATOR SGL R-R I/P 5.5V 8PIN UMAX - Tape and Reel |
| MAX941AUA-T | 制造商:Maxim Integrated Products 功能描述:HIGH-SPEED, LOW-POWER, 3V/5V, RAIL-TO-RAIL, SINGLE-SUPPLY CO - Tape and Reel |
| MAX941C/D | 功能描述:校驗器 IC RoHS:否 制造商:STMicroelectronics 產品: 比較器類型: 通道數量: 輸出類型:Push-Pull 電源電壓-最大:5.5 V 電源電壓-最小:1.1 V 補償電壓（最大值）:6 mV 電源電流（最大值）:1350 nA 響應時間: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SC-70-5 封裝:Reel |
| MAX941C/D DIE | 制造商:Maxim Integrated Products 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。