- 您現在的位置：買賣IC網 > PDF目錄11687 > MAX9271GTJ+ (Maxim Integrated Products)IC SERIALIZER 16BIT GMSL 32TQFN PDF資料下載
參數資料
| 型號： | MAX9271GTJ+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 31/49頁 |
| 文件大小： | 0K |
| 描述： | IC SERIALIZER 16BIT GMSL 32TQFN |
| 標準包裝： | 60 |
| 系列： | * |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁當前第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁
MAX9271
16-Bit GMSL Serializer with Coax or
STP Cable Drive
37
Maxim Integrated
Applications Information
PRBS Test
The serializer includes a PRBS pattern generator that
works with bit-error verification in the deserializer. To run
the PRBS test, set PRBSEN = 1 (0x04, D5) in the deserial-
izer and then in the serializer. To exit the PRBS test, set
PRBSEN = 0 (0x04, D5) in the serializer.
Error Generator
The serializer contains an error generator that enables
repeatable testing of the error-detection/correction fea-
tures of the GMSL link. Register 0x11 stores the configu-
ration bits for the error generator. A FC sets the error-
generation rate, type of errors, and the total number of
errors. The error generator is off by default.
Dual C Control
Usually systems have one FC to run the control channel,
located on the serializer side for video-display appli-
cations or on the deserializer side for image-sensing
applications. However, a FC can reside on each side
simultaneously and trade off running the control channel.
In this case, each FC can communicate with the serializer
and deserializer and any peripheral devices.
Contention occurs if both FC s attempt to use the control
channel at the same time. It is up to the user to prevent
this contention by implementing a higher-level protocol.
In addition, the control channel does not provide arbitra-
tion between I2C masters on both sides of the link. An
acknowledge frame is not generated when communica-
tion fails due to contention. If communication across the
serial link is not required, the FC s can disable the for-
ward and reverse control channel using the FWDCCEN
and REVCCEN bits (0x04, D[1:0]) in the serializer/dese-
rializer. Communication across the serial link is stopped
and contention between FC s cannot occur.
As an example of dual FC use in an image-sensing appli-
cation, the serializer can be in sleep mode, waiting for
wake-up by the FC on the deserializer side. After wake-
up, the serializer-side FC assumes master control of the
serializer’s registers.
Jitter-Filtering PLL
In some applications, the clock input (PCLKIN) includes
noise, which reduces link reliability. The clock input has a
programmable narrowband jitter-filter PLL that attenuates
frequencies higher than 100kHz (typ). Enable the jitter
filter by setting ENJITFILT = 1 (0x05, D6).
PCLKIN Spread Tracking
The serializer can operate with a spread PCLKIN
signal. When using a spread PCLKIN signal, disable the
jitter filter by setting ENJITFILT = 0 (0x05, D6). Do not
exceed the spread limitations listed in Table 7 and keep
modulation less than 40kHz. In addition, turn off spread
spectrum in the serializer/deserializer. The serializer/
deserializer track the spread on PCLKIN.
Changing the Clock Frequency
It is recommended that the serial link be enabled after
the video clock (fPCLKIN) and the control-channel clock
(fUART/fI2C) are stable. When changing clock frequency,
stop the video clock for 5Fs, apply the clock at the new
frequency, then restart the serial link or toggle SEREN.
On-the-fly changes in clock frequency are possible if
the new frequency is immediately stable and without
glitches. The reverse control channel remains unavail-
able for 350Fs after serial link start or stop. When using
the UART interface, limit on-the-fly changes in fUART to
factors of less than 3.5 at a time to ensure that the device
recognizes the UART sync pattern. For example, when
lowering the UART frequency from 1Mbps to 100kbps,
first send data at 333kbps, then at 100kbps for reduction
ratios of 3 and 3.333, respectively.
Providing a Frame Sync
(Camera Applications)
The GPI and GPO provide a simple solution for camera
applications that require a frame sync signal from the
ECU (e.g., surround-view systems). Connect the ECU
frame sync signal to the GPI input and connect the GPO
output to the camera frame sync input. GPI/GPO have
a typical delay of 275Fs. Skew between multiple GPI/
GPO channels is 115Fs (max). If a lower skew signal is
required, connect the camera’s frame sync input to one
of the serializer’s GPIOs and use an I2C broadcast write
command to change the GPIO output state. This has a
maximum skew of 1.5Fs, independent from the used I2C
bit rate.
Software Programming of the
Device Addresses
The serializer and deserializer have programmable device
addresses. This allows multiple GMSL devices, along with
I2C peripherals, to coexist on the same control channel.
The serializer device address is in register 0x00 of each
device, while the deserializer device address is in register
0x01 of each device. To change a device address, first
相關PDF資料 |
PDF描述 |
|---|---|
| MAX9218ETM+T | IC DESERIALIZER LVDS 48-TQFN |
| MAX9250ECM+T | IC DESERIALIZER LVDS 48-LQFP |
| MAX9260GCB/V+T | IC DESERIALIZER GMSL 64TQFP |
| MAX9259GCB/V+T | IC SERIALIZER GMSL 64TQFP |
| MAX9217ETM+T | IC SERIALIZER LVDS 48-TQFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX9271GTJ/V+ | 功能描述:串行器/解串器 - Serdes 1.5Gbps 16-bit Coax/STP serializer RoHS:否 制造商:Texas Instruments 類型:Deserializer 數據速率:1.485 Gbit/s 輸入類型:ECL/LVDS 輸出類型:LVCMOS 輸入端數量:1 輸出端數量:20 工作電源電壓:2.375 V to 2.625 V 工作溫度范圍:0 C to + 70 C 封裝 / 箱體:TQFP-64 |
| MAX9271GTJ/V+T | 功能描述:串行器/解串器 - Serdes 1.5Gbps 16-bit Coax/STP serializer RoHS:否 制造商:Texas Instruments 類型:Deserializer 數據速率:1.485 Gbit/s 輸入類型:ECL/LVDS 輸出類型:LVCMOS 輸入端數量:1 輸出端數量:20 工作電源電壓:2.375 V to 2.625 V 工作溫度范圍:0 C to + 70 C 封裝 / 箱體:TQFP-64 |
| MAX9271GTJ+ | 功能描述:串行器/解串器 - Serdes 1.5Gbps 16-bit Coax/STP serializer RoHS:否 制造商:Texas Instruments 類型:Deserializer 數據速率:1.485 Gbit/s 輸入類型:ECL/LVDS 輸出類型:LVCMOS 輸入端數量:1 輸出端數量:20 工作電源電壓:2.375 V to 2.625 V 工作溫度范圍:0 C to + 70 C 封裝 / 箱體:TQFP-64 |
| MAX9271GTJ+T | 功能描述:串行器/解串器 - Serdes 1.5Gbps 16Bit Coax/STP serializer RoHS:否 制造商:Texas Instruments 類型:Deserializer 數據速率:1.485 Gbit/s 輸入類型:ECL/LVDS 輸出類型:LVCMOS 輸入端數量:1 輸出端數量:20 工作電源電壓:2.375 V to 2.625 V 工作溫度范圍:0 C to + 70 C 封裝 / 箱體:TQFP-64 |
| MAX9272 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:28-Bit GMSL Deserializer for Coax or STP Cable |
發布緊急采購，3分鐘左右您將得到回復。