- 您現在的位置：買賣IC網 > PDF目錄1945 > MAX9153EUI+T (Maxim Integrated Products)IC REPEATER 10-PORT LVDS 28TSSOP PDF資料下載
參數資料
| 型號： | MAX9153EUI+T |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 10/11頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC REPEATER 10-PORT LVDS 28TSSOP |
| 標準包裝： | 2,500 |
| 系列： | * |
MAX9153/MAX9154
Low-Jitter, 800Mbps, 10-Port LVDS
Repeaters with 100
Ω Drive
8
_______________________________________________________________________________________
Applications Information
Supply Bypassing
Bypass each VCC with high-frequency surface-mount
ceramic 0.1F and 1nF capacitors in parallel as close
to the device as possible, with the smaller value capac-
itor closest to the VCC pin.
Traces, Cables, and Connectors
The characteristics of input and output connections
affect the performance of the MAX9153/MAX9154. Use
controlled-impedance traces, cables, and connectors
with matched characteristic impedance.
Ensure that noise couples as common mode by run-
ning the traces of a differential pair close together.
Reduce within-pair skew by matching the electrical
length of the traces of a differential pair. Excessive
skew can result in a degradation of magnetic field can-
cellation. Maintain the distance between traces of a dif-
ferential pair to avoid discontinuities in differential
impedance. Minimize the number of vias to further pre-
vent impedance discontinuities.
Avoid the use of unbalanced cables, such as ribbon
cable. Balanced cables, such as twisted pair, offer
superior signal quality and tend to generate less EMI
due to canceling effects. Balanced cables tend to pick
up noise as common mode, which is rejected by the
LVDS receiver.
Termination
The MAX9153/MAX9154 are specified for 100
Ω differ-
ential characteristic impedance but can operate with
90
Ω to 132Ω to accommodate various types of inter-
connect. The termination resistor should match the dif-
ferential characteristic impedance of the interconnect
and be located close to the LVDS receiver input. Use a
±1% surface-mount termination resistor.
The output voltage swing is determined by the value of the
termination resistor multiplied by the output current. With a
typical 3.8mA output current, the MAX9153/MAX9154 pro-
duce a 380mV output voltage when driving a transmission
line terminated with a 100
Ω resistor (3.8mA x 100Ω =
380mV).
Chip Information
TRANSISTOR COUNT: 1394
PROCESS: CMOS
Figure 3. Driver-Load Test Circuit
RIN+
RIN-
GENERATOR
50
Ω
50
Ω
MAX9153
MAX9154
DO1+
DO10+
DO10-
DO1-
VOD
VOS
50
Ω
50
Ω
50
Ω
50
Ω
VOS
VOD
Test Circuits and Timing Diagrams
相關PDF資料 |
PDF描述 |
|---|---|
| MAX9157EGJ+T | IC TXRX QUAD LVDS 32-TQFN |
| MAX9163ESA+T | IC TXRX LVDS BUS 3.3V 8-SOIC |
| MAX9171EKA+T | IC RECEIVER LVDS LINE SOT23-8 |
| MAX9175EUB+T | IC SPLITTR ANYTHING-LVDS 10UMAX |
| MAX9177EUB+T | IC MULTIPLEXER 2X1 10UMAX |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX9154 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Low-Jitter.800Mbps.10-Port LVDS Repeaters with 100＜img src=http://dbserv.maxim-ic.com/images/ohm.gif width=12 height=9 Drive |
| MAX9154EUI | 制造商:Maxim Integrated Products 功能描述:LOW-JITTER, 800MBPS, 10-PORT LVDS REPEATERS W - Rail/Tube |
| MAX9154EUI+ | 制造商:Maxim Integrated Products 功能描述:LVDS REPEATER 0.45V 28TSSOP - Rail/Tube |
| MAX9154EUI+T | 制造商:Maxim Integrated Products 功能描述:LVDS REPEATER 0.45V 28TSSOP - Tape and Reel |
| MAX9155 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Low-Jitter, Low-Noise LVDS Repeater in an SC70 Package |
發布緊急采購，3分鐘左右您將得到回復。