- 您現在的位置：買賣IC網 > PDF目錄1945 > MAX9150EUI+T (Maxim Integrated Products)IC REPEATER LVDS 28-TSSOP PDF資料下載
參數資料
| 型號： | MAX9150EUI+T |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 7/10頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC REPEATER LVDS 28-TSSOP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 2,500 |
| 類型： | 轉發器 |
| Tx/Rx類型： | LVDS |
| 延遲時間： | 2.2ns |
| 電源電壓： | 3 V ~ 3.6 V |
| 電流 - 電源： | 130mA |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 28-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 28-TSSOP |
| 包裝： | 帶卷 (TR) |
Detailed Description
The LVDS interface standard is a signaling method
intended for point-to-point communication over a con-
trolled impedance medium, as defined by the
ANSI/TIA/EIA-644 and IEEE 1596.3 standards. The
LVDS standard uses a lower voltage swing than other
common communication standards, achieving higher
data rates with reduced power consumption while
reducing EMI emissions and system susceptibility to
noise.
The MAX9150 is a 400Mbps, 10-port LVDS repeater
intended for high-speed, point-to-point, low-power
applications. This device accepts an LVDS input and
repeats it on 10 LVDS outputs. The device is capable of
detecting differential signals as low as 100mV and as
high as 1V within a 0 to 2.4V input voltage range. The
LVDS standard specifies an input voltage range of 0 to
2.4V referenced to ground.
The MAX9150 outputs use a current-steering configura-
tion to generate a 5mA to 9mA output current. This cur-
rent-steering approach induces less ground bounce
and no shoot-through current, enhancing noise margin
and system speed performance. The driver outputs are
short-circuit current limited, and are high impedance
(to ground) when
PWRDN = low or the device is not
powered. The outputs have a typical differential resis-
tance of 240Ω.
The MAX9150 current-steering architecture requires a
resistive load to terminate the signal and complete the
transmission loop. Because the device switches the
direction of current flow and not voltage levels, the out-
put voltage swing is determined by the total value of
the termination resistors multiplied by the output cur-
rent. With a typical 6.4mA output current, the MAX9150
produces a 320mV output voltage when driving a trans-
mission line terminated at each end with a 100Ω termi-
nation resistor (6.4mA x 50Ω = 320mV). Logic states
are determined by the direction of current flow through
the termination resistors.
Fail-Safe
Fail-safe is a receiver feature that puts the output in a
known logic state (high) under certain fault conditions.
The MAX9150 outputs are differential high when the
inputs are undriven and open, terminated, or shorted
(Table 1).
MAX9150
Low-Jitter, 10-Port LVDS Repeater
6
_______________________________________________________________________________________
Table 1. Input/Output Function Table
INPUT, VID
OUTPUTS, VOD
+100mV
High
-100mV
Low
Open
High
Short
High
Terminated
Undriven
High
Note: VID = RIN+ - RIN-, VOD = DO_+ - DO_-
High = 450mV > VOD > 250mV
Low = -250mV > VOD > -450mV
PIN
NAME
FUNCTION
1, 3, 11, 13,
16, 18, 20,
24, 26, 28
DO2+, DO1+, DO10+,
DO9+, DO8+, DO7+,
DO6+, DO5+, DO4+, DO3+
2, 4, 12, 14,
15, 17, 19,
23, 25, 27
DO2-, DO1-, DO10-, DO9-,
DO8-, DO7-,
DO6-, DO5-, DO4-, DO3-
Differential LVDS Outputs. Connect a 100
Ω resistor across each of the output
pairs (DO_+ and DO_-) adjacent to the IC, and connect a 100
Ω resistor at the
input of the receiving circuit.
5
PWRDN
Power Down. Drive PWRDN low to disable all outputs and reduce supply current
to 60A. Drive PWRDN high for normal operation.
6, 9, 21
GND
Ground
10, 22
VCC
Power. Bypass each VCC pin to GND with 0.1F and 1nF ceramic capacitors.
7
RIN+
8
RIN-
LVDS Receiver Inputs. RIN+ and RIN- are high-impedance inputs. Connect a
resistor from RIN+ to RIN- to terminate the input signal.
Pin Description
相關PDF資料 |
PDF描述 |
|---|---|
| MAX9152ESE+T | IC CROSSPOINT SWITCH 2X2 16SOIC |
| MAX9153EUI+T | IC REPEATER 10-PORT LVDS 28TSSOP |
| MAX9157EGJ+T | IC TXRX QUAD LVDS 32-TQFN |
| MAX9163ESA+T | IC TXRX LVDS BUS 3.3V 8-SOIC |
| MAX9171EKA+T | IC RECEIVER LVDS LINE SOT23-8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX9150EVKIT | 制造商:Maxim Integrated Products 功能描述:EVALUATION KIT FOR THE MAX9150 - Boxed Product (Development Kits) |
| MAX9152 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:800Mbps LVDS/LVPECL-to-LVDS 2 x 2 Crosspoint Switch |
| MAX9152ESE | 功能描述:模擬和數字交叉點 IC RoHS:否 制造商:Micrel 配置:2 x 2 封裝 / 箱體:MLF-16 數據速率:10.7 Gbps 輸入電平:CML, LVDS, LVPECL 輸出電平:CML 電源電壓-最大:3.6 V 電源電壓-最小:2.375 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 產品:Digital Crosspoint 封裝:Tube |
| MAX9152ESE+ | 功能描述:模擬和數字交叉點 IC LVDS/LVPECL-to-LVDS 2x2 Crosspoint Swtch RoHS:否 制造商:Micrel 配置:2 x 2 封裝 / 箱體:MLF-16 數據速率:10.7 Gbps 輸入電平:CML, LVDS, LVPECL 輸出電平:CML 電源電壓-最大:3.6 V 電源電壓-最小:2.375 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 產品:Digital Crosspoint 封裝:Tube |
| MAX9152ESE+T | 功能描述:模擬和數字交叉點 IC LVDS/LVPECL-to-LVDS 2x2 Crosspoint Swtch RoHS:否 制造商:Micrel 配置:2 x 2 封裝 / 箱體:MLF-16 數據速率:10.7 Gbps 輸入電平:CML, LVDS, LVPECL 輸出電平:CML 電源電壓-最大:3.6 V 電源電壓-最小:2.375 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 產品:Digital Crosspoint 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。