- 您現在的位置：買賣IC網 > PDF目錄383538 > MAX9117 (Maxim Integrated Products, Inc.) SC70, 1.8V, Nanopower, Beyond-the-Rails Comparators With/Without Reference PDF資料下載
參數資料
| 型號： | MAX9117 |
| 廠商： | Maxim Integrated Products, Inc. |
| 英文描述： | SC70, 1.8V, Nanopower, Beyond-the-Rails Comparators With/Without Reference |
| 中文描述： | SC70封裝、1.8V、納安級功耗、超擺幅比較器，帶或不帶電壓基準 |
| 文件頁數： | 10/13頁 |
| 文件大?。?/td> | 336K |
| 代理商： | MAX9117 |
M
SC70, 1.8V, Nanopower, Beyond-the-Rails
Comparators With/Without Reference
10
______________________________________________________________________________________
Reference (MAX9117/MAX9118)
The internal reference in the MAX9117/MAX9118 has an
output voltage of +1.252V with respect to V
EE
. Its typical
temperature coefficient is 100ppm/
°
C over the full
-40
°
C to +85
°
C temperature range. The reference is a
PNP emitter-follower driven by a 120nA current source
(Figure 1). The output impedance of the voltage refer-
ence is typically 200k
, preventing the reference from
driving large loads. The reference can be bypassed with
a low-leakage capacitor. The reference is stable for any
capacitive load. For applications requiring a lower output
impedance, buffer the reference with a low-input-leak-
age op amp, such as the MAX4162.
Applications Information
Low-Voltage, Low-Power Operation
The MAX9117
–
MAX9120 are ideally suited for use with
most battery-powered systems. Table 1 lists a variety of
battery types, capacities, and approximate operating
times for the MAX9117
–
MAX9120, assuming nominal
conditions.
Internal Hysteresis
Many comparators oscillate in the linear region of oper-
ation because of noise or undesired parasitic feed-
back. This tends to occur when the voltage on one
input is equal or very close to the voltage on the other
input. The MAX9117
–
MAX9120 have internal hysteresis
to counter parasitic effects and noise.
The hysteresis in a comparator creates two trip points:
one for the rising input voltage (V
THR
) and one for the
falling input voltage (V
THF
) (Figure 2). The difference
between the trip points is the hysteresis (V
HB
). When
the comparator
’
s input voltages are equal, the hystere-
sis effectively causes one comparator input to move
quickly past the other, thus taking the input out of the
region where oscillation occurs. Figure 2 illustrates the
case in which IN- has a fixed voltage applied, and IN+
is varied. If the inputs were reversed, the figure would
be the same, except with an inverted output.
Additional Hysteresis (MAX9117/MAX9119)
The MAX9117/MAX9119 have a 4mV internal hysteresis
band (V
HB
). Additional hysteresis can be generated
with three resistors using positive feedback (Figure 3).
Unfortunately, this method also slows hysteresis re-
sponse time. Use the following procedure to calculate
resistor values.
1) Select R3. Leakage current at IN is under 2nA, so the
current through R3 should be at least 0.2μA to mini-
mize errors caused by leakage current. The current
through R3 at the trip point is (V
REF
- V
OUT
) / R3.
Considering the two possible output states in solving
for R3 yields two formulas: R3 = V
REF
/ I
R3
or R3 =
(V
CC
- V
REF
) / I
R3
. Use the smaller of the two result-
ing resistor values. For example, when using the
120nA
REF
V
CC
V
EE
V
BIAS
Figure 1. MAX9117/MAX9118 Voltage Reference Output
Equivalent Circuit
Table 1. Battery Applications Using MAX9117
–
MAX9120
BATTERY
TYPE
RECHARGEABLE
V
FRESH
(V)
V
END-OF-LIFE
(V)
CAPACITY,
AA SIZE
(mA-h)
MAX9117/MAX9118
OPERATING TIME
(hr)
Alkaline
(2 Cells)
No
3.0
1.8
2000
2.5 x 10
6
Nickel-Cadmium
(2 Cells)
Yes
2.4
1.8
750
937,500
1.25 x 10
6
1000
2.7
3.5
Yes
Lithium-Ion
(1 Cell)
Nickel-Metal-
Hydride
(2 Cells)
Yes
2.4
1.8
1000
1.25 x 10
6
MAX9119/MAX9120
OPERATING TIME
(hr)
5 x 10
6
1.875 x 10
6
2.5 x 10
6
2.5 x 10
6
相關PDF資料 |
PDF描述 |
|---|---|
| MAX9119 | SC70, 1.8V, Nanopower, Beyond-the-Rails Comparators With/Without Reference |
| MAX9117EXK-T | SC70, 1.8V, Nanopower, Beyond-the-Rails Comparators With/Without Reference |
| MAX9119EXK-T | SC70, 1.8V, Nanopower, Beyond-the-Rails Comparators With/Without Reference |
| MAX911CAG | Analog Comparator |
| MAX9174 | 670MHz LVDS-to-LVDS and Anything-to-LVDS 1:2 Splitters |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX9117ESA | 功能描述:校驗器 IC RoHS:否 制造商:STMicroelectronics 產品: 比較器類型: 通道數量: 輸出類型:Push-Pull 電源電壓-最大:5.5 V 電源電壓-最小:1.1 V 補償電壓（最大值）:6 mV 電源電流（最大值）:1350 nA 響應時間: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SC-70-5 封裝:Reel |
| MAX9117ESA+ | 功能描述:校驗器 IC SC70 1.6V Nanopower Beyond-the-Rails Comparators With/Without Reference RoHS:否 制造商:STMicroelectronics 產品: 比較器類型: 通道數量: 輸出類型:Push-Pull 電源電壓-最大:5.5 V 電源電壓-最小:1.1 V 補償電壓（最大值）:6 mV 電源電流（最大值）:1350 nA 響應時間: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SC-70-5 封裝:Reel |
| MAX9117ESA+T | 功能描述:校驗器 IC SC70 1.6V Nanopower Beyond-the-Rails Comparators With/Without Reference RoHS:否 制造商:STMicroelectronics 產品: 比較器類型: 通道數量: 輸出類型:Push-Pull 電源電壓-最大:5.5 V 電源電壓-最小:1.1 V 補償電壓（最大值）:6 mV 電源電流（最大值）:1350 nA 響應時間: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SC-70-5 封裝:Reel |
| MAX9117ESA-T | 功能描述:校驗器 IC RoHS:否 制造商:STMicroelectronics 產品: 比較器類型: 通道數量: 輸出類型:Push-Pull 電源電壓-最大:5.5 V 電源電壓-最小:1.1 V 補償電壓（最大值）:6 mV 電源電流（最大值）:1350 nA 響應時間: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SC-70-5 封裝:Reel |
| MAX9117EXK | 制造商:Maxim Integrated Products 功能描述:SC70, 1.8V, NANOPOWER, BEYOND-THE-RAILS COMPARATOR W/WO REF - Cut Tape Product |
發布緊急采購，3分鐘左右您將得到回復。