- 您現在的位置：買賣IC網 > PDF目錄383537 > MAX9040 (Maxim Integrated Products, Inc.) Micropower, Single-Supply, SOT23 Comparator + Precision Reference ICs PDF資料下載
參數資料
| 型號： | MAX9040 |
| 廠商： | Maxim Integrated Products, Inc. |
| 英文描述： | Micropower, Single-Supply, SOT23 Comparator + Precision Reference ICs |
| 中文描述： | 微功耗、單電源、UCSP/SOT23封裝的比較器 + 精密電壓基準IC |
| 文件頁數： | 9/12頁 |
| 文件大小： | 162K |
| 代理商： | MAX9040 |
Detailed Description
The MAX9040–MAX9043 and MAX9050–MAX9053 fea-
ture single/dual, low-power, low-voltage comparators
and a precision voltage reference. They operate from a
single +2.5V to +5.5V (MAX904_) or +2.7V to +5.5V
(MAX905_) supply. The single comparators with refer-
ence (MAX9040/MAX9041/MAX9050/MAX9051) con-
sume only 40μA of supply current, while the dual
comparators with reference (MAX9042/MAX9043/
MAX9052/MAX9053) consume only 55μA of supply cur-
rent. Their common-mode input range extends 0.25V
beyond each rail. Internal hysteresis ensures clean out-
put switching, even with slow-moving input signals.
The output stage employs a unique design that mini-
mizes supply current surges while switching, virtually
eliminating the supply glitches typical of many other
comparators. Large internal output drivers allow rail-to-
rail output swing that can sink and source up to 8mA of
current.
The precision reference uses a proprietary curvature-
correction circuit and laser-trimmed thin-film resistors,
resulting in a temperature coefficient of less than
30ppm/°C over the extended temperature range and
initial accuracy of 0.4% (A grade). The reference output
voltage is set to 2.048V in the MAX9040–MAX9043 and
to 2.500V in the MAX9050–MAX9053.
Comparator Input Stage Circuitry
The devices’ input common-mode range extends from
(V
EE
- 0.25V) to (V
CC
+ 0.25V). These comparators may
operate at any differential input voltage within these lim-
its. Input bias current is typically 1.0pA if the input volt-
age is between the supply rails. Comparator inputs are
protected from overvoltage by internal body diodes
connected to the supply rails. As the input voltage
exceeds the supply rails, these body diodes become
forward biased and begin to conduct. Consequently,
bias currents increase exponentially as the input volt-
age exceeds the supply rails.
Comparator Output Stage Circuitry
The comparators in these devices contain a unique
output stage capable of rail-to-rail operation with loads
up to 8mA. Many comparators consume orders-of-mag-
nitude more current during switching than during
steady-state operation. However, with this family of com-
parators, the supply current change during an output
transition is extremely small. The
Typical Operating
Characteristics
graph Supply Current vs. Switching
Frequency shows the minimal supply current increase
as the output switching frequency approaches 1MHz.
This characteristic reduces the need for power-supply
filter capacitors to reduce glitches created by compara-
tor switching currents. Another advantage realized in
high-speed, battery-powered applications is a substan-
tial increase in battery life.
Applications Information
Additional Hysteresis
These comparators have ±3mV internal hysteresis.
Additional hysteresis can be generated with two resis-
tors using positive feedback (Figure 1). Use the follow-
ing procedure to calculate resistor values:
1) Calculate the trip points of the comparator using
these formulas:
and
V
TH
is the threshold voltage at which the comparator
switches its output from high to low as V
IN
rises
above the trip point. V
TL
is the threshold voltage at
which the comparator switches its output from low to
high as V
IN
drops below the trip point.
2) The hysteresis band will be:
V
HYS
= V
TH
- V
TL
= V
CC
R
+
R
R
2
1
2
V
V
R
+
R
R
TL
REF
=
1
2
1
2
V
V
V
V
R
R
R
TH
REF
CC
REF
=
+
(
)
+
2
1
2
M
Micropower, Single-Supply,
SOT23 Comparator + Precision Reference ICs
_______________________________________________________________________________________
9
MAX9040–9043
MAX9050–9053
V
EE
OUT
IN+
IN-
R2
R1
V
IN
V
REF
V
CC
V
CC
Figure 1. Additional Hysteresis
相關PDF資料 |
PDF描述 |
|---|---|
| MAX9040AEUK-T | Micropower, Single-Supply, SOT23 Comparator + Precision Reference ICs |
| MAX9040BEUK-T | Micropower, Single-Supply, SOT23 Comparator + Precision Reference ICs |
| MAX9042 | Micropower, Single-Supply, UCSP/SOT23 Comparator + Precision Reference ICs |
| MAX9042AESA | Micropower, Single-Supply, SOT23 Comparator + Precision Reference ICs |
| MAX9042BESA | Micropower, Single-Supply, SOT23 Comparator + Precision Reference ICs |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX9040AEUK | 制造商:Maxim Integrated Products 功能描述:MICROPOWER SINGLE-SUPPLY SOT23 CO - Cut Tape Product |
| MAX9040AEUK+ | 制造商:Maxim Integrated Products 功能描述:COMPARATOR SGL R-R I/O 5.5V 5PIN SOT-23 - Rail/Tube |
| MAX9040AEUK+T | 功能描述:校驗器 IC uPower Comparator + Prec Reference IC RoHS:否 制造商:STMicroelectronics 產品: 比較器類型: 通道數量: 輸出類型:Push-Pull 電源電壓-最大:5.5 V 電源電壓-最小:1.1 V 補償電壓（最大值）:6 mV 電源電流（最大值）:1350 nA 響應時間: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SC-70-5 封裝:Reel |
| MAX9040AEUK-T | 功能描述:校驗器 IC uPower Comparator + Prec Reference IC RoHS:否 制造商:STMicroelectronics 產品: 比較器類型: 通道數量: 輸出類型:Push-Pull 電源電壓-最大:5.5 V 電源電壓-最小:1.1 V 補償電壓（最大值）:6 mV 電源電流（最大值）:1350 nA 響應時間: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SC-70-5 封裝:Reel |
| MAX9040BEUK | 制造商:Maxim Integrated Products 功能描述:MICROPOWER SINGLE-SUPPLY SOT23 CO - Cut Tape Product |
發布緊急采購，3分鐘左右您將得到回復。