- 您現在的位置：買賣IC網 > PDF目錄385553 > MAX8864R (Maxim Integrated Products, Inc.) Low-Dropout, 100mA Linear Regulators(100mA,低壓差線性穩壓器,SOT23封裝) PDF資料下載
參數資料
| 型號： | MAX8864R |
| 廠商： | Maxim Integrated Products, Inc. |
| 英文描述： | Low-Dropout, 100mA Linear Regulators(100mA,低壓差線性穩壓器,SOT23封裝) |
| 中文描述： | 低壓差、120mA線性穩壓器 |
| 文件頁數： | 8/12頁 |
| 文件大小： | 129K |
| 代理商： | MAX8864R |
M
Low-Dropout, 100mA Linear Regulators
8
_______________________________________________________________________________________
Operating Region and Power Dissipation
Maximum power dissipation of the MAX8863/MAX8864
depends on the thermal resistance of the case and cir-
cuit board, the temperature difference between the die
junction and ambient air, and the rate of air flow. The
power dissipation across the device is P = I
OUT
(V
IN
-
V
OUT
). The resulting maximum power dissipation is:
P
MAX
= (T
J
- T
A
) /
θ
J A
where (T
J
- T
A
) is the temperature difference between
the MAX8863/MAX8864 die junction and the surround-
ing air, and
θ
J A
is the thermal resistance of the chosen
package to the surrounding air.
The GND pin of the MAX8863/MAX8864 performs the
dual function of providing an electrical connection to
ground and channeling heat away. Connect the GND
pin to ground using a large pad or ground plane.
Reverse Battery Protec tion
The MAX8863/MAX8864 have a unique protection
scheme that limits the reverse supply current to less
than 1mA when either V
IN
or V
SHDN
falls below ground.
The circuitry monitors the polarity of these two pins, dis-
connecting the internal circuitry and parasitic diodes
when the battery is reversed. This feature prevents the
device from overheating and damaging the battery.
__________Applic ations Information
Capac itor S elec tion and
Regulator S tability
Normally, use a 1μF capacitor on the input and a 1μF
capacitor on the output of the MAX8863/MAX8864.
Larger input capacitor values and lower ESR provide
better supply-noise rejection and transient response. A
higher-value input capacitor (10μF) may be necessary
if large, fast transients are anticipated and the device is
located several inches from the power source. Improve
load-transient response, stability, and power-supply
rejection by using large output capacitors. For stable
operation over the full temperature range, with load cur-
rents up to 100mA, a minimum of 1μF is recommended.
Noise
The MAX8863/MAX8864 exhibit 350μV
RMS
noise during
normal operation. When using the MAX8863/MAX8864
in applications that include analog-to-digital converters
of greater than 12 bits, consider the ADC’s power-sup-
ply rejection specifications (see the Output Noise DC to
1MHz photo in the Typical Operating Characteristics).
Power-S upply Rejec tion and Operation
from S ourc es Other than Batteries
The MAX8863/MAX8864 are designed to deliver low
dropout voltages and low quiescent currents in battery-
powered systems. Power-supply rejection is 62dB at
low frequencies and rolls off above 300Hz. As the fre-
quency increases above 20kHz, the output capacitor is
the major contributor to the rejection of power-supply
noise (see the Power-Supply Rejection Ratio vs.
Ripple Frequency graph in the Typical Operating
Characteristics).
When operating from sources other than batteries,
improve supply-noise rejection and transient response
by increasing the values of the input and output capac-
itors, and using passive filtering techniques (see the
supply and load-transient responses in the Typical
Operating Characteristics).
Load T ransient Considerations
The MAX8863/MAX8864 load-transient response
graphs (see Typical Operating Characteristics) show
two components of the output response: a DC shift of
the output voltage due to the different load currents,
and the transient response. Typical overshoot for step
changes in the load current from 0mA to 50mA is
12mV. Increasing the output capacitor’s value and
decreasing its ESR attenuates transient spikes.
Input-Output (Dropout) V oltage
A regulator’s minimum input-output voltage differential
(or dropout voltage) determines the lowest usable sup-
ply voltage. In battery-powered systems, this will deter-
mine the useful end-of-life battery voltage. Because the
MAX8863/MAX8864 use a P-channel MOSFET pass
transistor, their dropout voltage is a function of R
multiplied by the load current (see Electrical
Characteristics).
___________________Chip Information
TRANSISTOR COUNT: 148
相關PDF資料 |
PDF描述 |
|---|---|
| MAX8864S | Low-Dropout, 100mA Linear Regulators(100mA,低壓差線性穩壓器,SOT23封裝) |
| MAX8864T | Low-Dropout, 100mA Linear Regulators(100mA,低壓差線性穩壓器,SOT23封裝) |
| MAX8865 | Dual, Low-Dropout, 100mA Linear Regulators(雙組,低輸出壓降,100mA線性穩壓器) |
| MAX8866 | Dual, Low-Dropout, 100mA Linear Regulators(雙組,低輸出壓降,100mA線性穩壓器) |
| MAX8875EUK30-T | 150mA, Low-Dropout Linear Regulator with Power-OK Output |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX8864REUK | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| MAX8864REUK+ | 制造商:Maxim Integrated Products 功能描述:LDO REG 1.225V TO 6.5V/2.8V 0.12A 5PIN SOT-23 - Rail/Tube |
| MAX8864REUK+T | 功能描述:低壓差穩壓器 - LDO 120mA Linear Regulator RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| MAX8864REUK-T | 功能描述:低壓差穩壓器 - LDO 120mA Linear Regulator RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| MAX8864SEUK | 制造商:Maxim Integrated Products 功能描述:- Rail/Tube 制造商:Rochester Electronics LLC 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。