- 您現在的位置：買賣IC網 > PDF目錄383513 > MAX8808X (Maxim Integrated Products, Inc.) 1A Linear Li+ Battery Chargers with Integrated Pass FET and Thermal Regulation in 2mm x 2mm TDFN PDF資料下載
參數資料
| 型號： | MAX8808X |
| 廠商： | Maxim Integrated Products, Inc. |
| 元件分類： | 基準電壓源/電流源 |
| 英文描述： | 1A Linear Li+ Battery Chargers with Integrated Pass FET and Thermal Regulation in 2mm x 2mm TDFN |
| 中文描述： | 第1A線性鋰電池充電器采用2mm x 2mm TDFN封裝與集成調整FET和熱調節 |
| 文件頁數： | 8/13頁 |
| 文件大小： | 236K |
| 代理商： | MAX8808X |
M
VL Internal Voltage Regulator
The MAX8808X/MAX8808Y/MAX8808Z linear chargers
contain an internal linear regulator to supply the power
for the IC. Bypass VL to GND with a 0.47μF ceramic
capacitor. VL is regulated to 3.0V whenever the input
voltage is above the battery voltage.
CHG
Charge-Indicator Output
CHG
is an open-drain output that indicates charge sta-
tus.
Table
1 describes the state of
CHG
during different
stages of operation.
CHG
is suitable for driving a
charge-indication LED. If the MAX8808X/MAX8808Y/
MAX8808Z is used in conjunction with a μP, a pullup
resistor to the logic I/O voltage allows
CHG
to indicate
charge status to the μP instead of driving an LED.
Soft-Start
The soft-start algorithm activates when entering fast-
charge mode. In the MAX8808X, when the prequalifica-
tion state is complete (V
BATT
exceeds +2.5V), the
charging current ramps up in 1ms to the full charging
current. This reduces the inrush current on the input
supply. Note that the MAX8808Y and MAX8808Z do not
have a prequalification state and enter soft-start directly
after being enabled.
Applications Information
Charge-Current Selection
The maximum charging current is programmed by an
external resistor connected from ISET to GND (R
ISET
).
Calculate R
ISET
as follows:
R
ISET
= 1302V / I
FASTCHG
where I
FASTCHG
is in Amps and R
ISET
is in Ohms. ISET
can be used to monitor the fast-charge current level.
The output current from ISET is 1.08mA per amp of
charging current. The output voltage at ISET is propor-
tional to the charging current:
V
ISET
= (I
CHARGE
x R
ISET
) / 930
The voltage at ISET is nominally 1.4V at the selected
fast-charge current, and falls with charging current as
the cell becomes fully charged or as the thermal-regu-
lation circuitry activates.
Capacitor Selection
Connect a ceramic capacitor from BATT to GND for
proper stability. Use a 1μF X5R ceramic capacitor for
most applications. Connect a 1μF ceramic capacitor
from IN to GND. Use a larger input bypass capacitor
for high charging currents to reduce supply noise.
Connect a 0.47μF ceramic capacitor from VL to GND.
Thermal Considerations
The MAX8808X/MAX8808Y/MAX8808Z are available in
a thermally enhanced TDFN package with exposed
paddle. Connect the exposed paddle to a large cop-
per ground plane to provide a thermal contact
between the device and the circuit board for increased
power dissipation. The exposed paddle transfers heat
away from the device, allowing the ICs to charge the
battery with maximum current, while minimizing the
increase in die temperature.
1A Linear Li+ Battery Chargers with Integrated Pass
FET and Thermal Regulation in 2mm x 2mm TDFN
8
_______________________________________________________________________________________
Table
1.
CHG
States
EN
MAX8808X
EN
MAX8808Y
EN
MAX8808Z
V
IN
V
BATT
I
BATT
CHG
STATE
X
X
—
X
—
Low
Low
Low
High
≤
V
BATT
≥
V
IN
<2.4V
≥
2.5V
4.2V
X
X
0
High-Impedance
Low
Low
High-Impedance
High-Impedance
High-Impedance
Shutdown
Prequal
Fast-Charge
Top-off
Shutdown
Disabled
Low
Low
Low
Low
High
4.25V
≤
V
IN
≤
7V
4.25V
≤
V
IN
≤
7V
4.25V
≤
V
IN
≤
7V
>7V
X
10% of I
FAST
I
FAST
*
<10% of I
FAST
0
0
High
High
High
Low
X = Don’t care.
— = Prequal not applicable to MAX8808Y and MAX8808Z.
*I
FAST
is reduced as necessary to prevent the die temperature from exceeding +115°C.
相關PDF資料 |
PDF描述 |
|---|---|
| MAX8808Y | 1A Linear Li+ Battery Chargers with Integrated Pass FET and Thermal Regulation in 2mm x 2mm TDFN |
| MAX8808Z | 1A Linear Li+ Battery Chargers with Integrated Pass FET and Thermal Regulation in 2mm x 2mm TDFN |
| MAX8808ZETA | Circular Connector; No. of Contacts:13; Series:TVS06; Body Material:Metal; Connecting Termination:Crimp; Connector Shell Size:11; Circular Contact Gender:Pin; Circular Shell Style:Straight Plug; Insert Arrangement:11-35 |
| MAX8808XETA | 1A Linear Li+ Battery Chargers with Integrated Pass FET and Thermal Regulation in 2mm x 2mm TDFN |
| MAX881REVKIT | Evaluation Kit for the MAX881R |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX8808XETA | 制造商:Maxim Integrated Products 功能描述:1A LINEAR LI+ BATT CHRGRS W. INTEG - Rail/Tube |
| MAX8808XETA+ | 制造商:Maxim Integrated Products 功能描述:CHRGR LI-ION/LI-POL 1000MA 4.2V 8TDFN EP - Rail/Tube |
| MAX8808XETA+T | 功能描述:電池管理 1A Linear Li+ Battery Charger RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| MAX8808XETA+TG104 | 功能描述:電池管理 1A Linear Li+ Battery Charger RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| MAX8808XETA-T | 功能描述:電池管理 RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。