- 您現在的位置：買賣IC網 > PDF目錄385553 > MAX858 (Maxim Integrated Products, Inc.) Step-Up DC-DC Converters(可調節輸出,高效率,低IQ值,步升DC-DC變換器) PDF資料下載
參數資料
| 型號： | MAX858 |
| 廠商： | Maxim Integrated Products, Inc. |
| 元件分類： | DC/DC變換器 |
| 英文描述： | Step-Up DC-DC Converters(可調節輸出,高效率,低IQ值,步升DC-DC變換器) |
| 中文描述： | 3.3V/5V或可調輸出、升壓型DC-DC轉換器 |
| 文件頁數： | 8/12頁 |
| 文件大?。?/td> | 152K |
| 代理商： | MAX858 |
M
3.3V /5V or Adjustable-Output,
S tep-Up DC-DC Converters
8
_______________________________________________________________________________________
Logic Inputs and Outputs
The 3/5 input is internally diode clamped
to GND
and
OUT, and should not be connected to signals outside
this range. The SHDN input and LBO output (open-
drain) are not clamped to V+ and can be pulled as high
as 7V regardless of the voltage at OUT
.
Do not leave
control inputs (3/5, LBI, or SHDN) floating.
__________________Design Proc edure
Output V oltage S elec tion
For the MAX856/MAX858,you can select a 3.3V or 5V
GND or OUT. Efficiency is typically better than 80%
over a 2mA to 100mA (MAX856/MAX857) load range.
The device is internally bootstrapped, with power
derived from the output voltage (via OUT). When the
output is in 5V mode, the higher internal supply voltage
results in lower switch-transistor on-resistance, slightly
greater output power, and higher efficiency.
Bootstrapping allows the battery voltage to sag to 0.8V
once the system is started. Therefore, the battery volt-
age ranges from (V
OUT
+ V
D
) to 0.8V (where V
D
is the
forward drop of the Schottky rectifier). If the battery volt-
age exceeds the programmed output voltage, the out-
put will follow the battery voltage. This is acceptable in
many systems; however, the input or output voltage
must not be forced above 7V.
The MAX857/MAX859’s output voltage is set by two
resistors, R1 and R2 (Figure 2b), which form a voltage
divider between the output and FB. Use the following
equation to determine the output voltage:
V
OUT
= V
REF
( R1 + R2
R2
where V
REF
= 1.25V.
To simplify resistor selection:
OUT
V
REF
R1 = R2 ( V
Since the input bias current at FB has a maximum value
of 100nA, large values (10k
to 300k
) can be used
for R1 and R2 with no significant accuracy loss. For 1%
error, the current through R1 should be at least 100
times FB’s bias current.
C1*
L1
D1
1N5817
V
IN
C2*
R1
R2
LX
OUT
FB
LBO
LBI
REF
SHDN
GND
R3
R4
C3
0.1
μ
F
V
OUT
5
1
3
8
6
2
4
7
MAX857/MAX859
*C1 = C2 = 68
μ
F FOR MAX857
C1 = C2 = 22
μ
F FOR MAX859
47
μ
H
C1*
L1
D1
1N5817
V
IN
C2*
R1
LX
OUT
3/5
LBO
LBI
REF
SHDN
GND
R3
R4
C3
0.1
μ
F
V
OUT
5
1
3
8
6
2
4
7
MAX856/MAX858
*C1 = C2 = 68
μ
F FOR MAX856
C1 = C2 = 22
μ
F FOR MAX858
OUTPUT
SELECT
47
μ
H
Figure 2b. Standard Application Circuit—Adjustable Output
Voltage
Figure 2a. Standard Application Circuit—Preset Output
Voltage
相關PDF資料 |
PDF描述 |
|---|---|
| MAX860CSA | DC-to-DC Voltage Converter |
| MAX860CUA | DC-to-DC Voltage Converter |
| MAX861CSA | DC-to-DC Voltage Converter |
| MAX861CUA | DC-to-DC Voltage Converter |
| MAX863EKE | Analog IC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX8581ETB+T | 功能描述:直流/直流開關轉換器 2.5/1.5MHz Step-Down Converter RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| MAX8582ETB+ | 制造商:Maxim Integrated Products 功能描述: |
| MAX8582ETB+T | 功能描述:直流/直流開關轉換器 2.5/1.5MHz Step-Down Converter RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| MAX8582EVKIT+ | 制造商:Maxim Integrated Products 功能描述:MAX8582 EVAL KIT - Rail/Tube |
| MAX8585EUA | 功能描述:功率驅動器IC RoHS:否 制造商:Micrel 產品:MOSFET Gate Drivers 類型:Low Cost High or Low Side MOSFET Driver 上升時間: 下降時間: 電源電壓-最大:30 V 電源電壓-最小:2.75 V 電源電流: 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。