- 您現在的位置：買賣IC網 > PDF目錄384708 > MAX856-MAX859 (Maxim Integrated Products, Inc.) 3-Line To 8-Line Decoders/Demultiplexers 16-CDIP -55 to 125 PDF資料下載
參數資料
| 型號： | MAX856-MAX859 |
| 廠商： | Maxim Integrated Products, Inc. |
| 英文描述： | 3-Line To 8-Line Decoders/Demultiplexers 16-CDIP -55 to 125 |
| 中文描述： | 3.3V/5V的或可調輸出，升壓型DC - DC轉換器 |
| 文件頁數： | 8/12頁 |
| 文件大?。?/td> | 126K |
| 代理商： | MAX856-MAX859 |
M
3.3V /5V or Adjustable-Output,
S tep-Up DC-DC Converters
8
_______________________________________________________________________________________
Logic Inputs and Outputs
The 3/5 input is internally diode clamped
to GND
and
OUT, and should not be connected to signals outside
this range. The SHDN input and LBO output (open-
drain) are not clamped to V+ and can be pulled as high
as 7V regardless of the voltage at OUT
.
Do not leave
control inputs (3/5, LBI, or SHDN) floating.
__________________Design Proc edure
Output V oltage S elec tion
For the MAX856/MAX858,you can select a 3.3V or 5V
GND or OUT. Efficiency is typically better than 80%
over a 2mA to 100mA (MAX856/MAX857) load range.
The device is internally bootstrapped, with power
derived from the output voltage (via OUT). When the
output is in 5V mode, the higher internal supply voltage
results in lower switch-transistor on-resistance, slightly
greater output power, and higher efficiency.
Bootstrapping allows the battery voltage to sag to 0.8V
once the system is started. Therefore, the battery volt-
age ranges from (V
OUT
+ V
D
) to 0.8V (where V
D
is the
forward drop of the Schottky rectifier). If the battery volt-
age exceeds the programmed output voltage, the out-
put will follow the battery voltage. This is acceptable in
many systems; however, the input or output voltage
must not be forced above 7V.
The MAX857/MAX859’s output voltage is set by two
resistors, R1 and R2 (Figure 2b), which form a voltage
divider between the output and FB. Use the following
equation to determine the output voltage:
V
OUT
= V
REF
( R1 + R2
R2
where V
REF
= 1.25V.
To simplify resistor selection:
OUT
V
REF
R1 = R2 ( V
Since the input bias current at FB has a maximum value
of 100nA, large values (10k
to 300k
) can be used
for R1 and R2 with no significant accuracy loss. For 1%
error, the current through R1 should be at least 100
times FB’s bias current.
C1*
L1
D1
1N5817
V
IN
C2*
R1
R2
LX
OUT
FB
LBO
LBI
REF
SHDN
GND
R3
R4
C3
0.1
μ
F
V
OUT
5
1
3
8
6
2
4
7
MAX857/MAX859
*C1 = C2 = 68
μ
F FOR MAX857
C1 = C2 = 22
μ
F FOR MAX859
47
μ
H
C1*
L1
D1
1N5817
V
IN
C2*
R1
LX
OUT
3/5
LBO
LBI
REF
SHDN
GND
R3
R4
C3
0.1
μ
F
V
OUT
5
1
3
8
6
2
4
7
MAX856/MAX858
*C1 = C2 = 68
μ
F FOR MAX856
C1 = C2 = 22
μ
F FOR MAX858
OUTPUT
SELECT
47
μ
H
Figure 2b. Standard Application Circuit—Adjustable Output
Voltage
Figure 2a. Standard Application Circuit—Preset Output
Voltage
相關PDF資料 |
PDF描述 |
|---|---|
| MAX856CSA | Dual 2-Line To 4-Line Decoders/Demultiplexers 16-CDIP -55 to 125 |
| MAX856CUA | Dual 2-Line To 4-Line Decoders/Demultiplexers 16-CFP -55 to 125 |
| MAX856ESA | Dual 2-Line To 4-Line Decoders/Demultiplexers 16-CDIP -55 to 125 |
| MAX856MJA | Dual 2-Line To 4-Line Decoders/Demultiplexers 20-LCCC -55 to 125 |
| MAX857 | Dual 2-Line To 4-Line Decoders/Demultiplexers 16-CDIP -55 to 125 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX8570ELT+ | 制造商:Maxim Integrated Products 功能描述:- Rail/Tube |
| MAX8570ELT+T | 功能描述:LCD 驅動器 High-Efficiency LCD Boost RoHS:否 制造商:Maxim Integrated 數位數量:4.5 片段數量:30 最大時鐘頻率:19 KHz 工作電源電壓:3 V to 3.6 V 最大工作溫度:+ 85 C 最小工作溫度:- 20 C 封裝 / 箱體:PDIP-40 封裝:Tube |
| MAX8570ELT+TG47 | 功能描述:LCD 驅動器 High-Efficiency LCD Boost with True Shutdown RoHS:否 制造商:Maxim Integrated 數位數量:4.5 片段數量:30 最大時鐘頻率:19 KHz 工作電源電壓:3 V to 3.6 V 最大工作溫度:+ 85 C 最小工作溫度:- 20 C 封裝 / 箱體:PDIP-40 封裝:Tube |
| MAX8570EUT | 制造商:Maxim Integrated Products 功能描述:HI-EFFICIENCY 15V LCD STEP-UP DC-DC - Rail/Tube |
| MAX8570EUT+ | 制造商:Maxim Integrated Products 功能描述:LCD DRVR 2.7V TO 5.5V 6PIN SOT-23 - Rail/Tube |
發布緊急采購，3分鐘左右您將得到回復。