- 您現在的位置：買賣IC網 > PDF目錄383507 > MAX810TEUR-T10 (MAXIM INTEGRATED PRODUCTS INC) 3-Pin Microprocessor Reset Circuits PDF資料下載
參數資料
| 型號： | MAX810TEUR-T10 |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 電源管理 |
| 英文描述： | 3-Pin Microprocessor Reset Circuits |
| 中文描述： | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO3 |
| 封裝： | SOT-23, 3 PIN |
| 文件頁數： | 5/8頁 |
| 文件大小： | 136K |
| 代理商： | MAX810TEUR-T10 |
M
_______________________________________________________________________________________
5
Detailed Description
A microprocessor’s (μP’s) reset input starts the μP in a
known state. The MAX803/MAX809/MAX810 assert
reset to prevent code-execution errors during power-
up, power-down, or brownout conditions. They assert a
reset signal whenever the V
CC
supply voltage declines
below a preset threshold, keeping it asserted for at
least 140ms after V
CC
has risen above the reset thresh-
old. The MAX803 uses an open-drain output, and the
MAX809/MAX810 have a push-pull output stage.
Connect a pull-up resistor on the MAX803’s
RESET
out-
put to any supply between 0 and 6V.
Applications Information
Negative-Going V
CC
Transients
In addition to issuing a reset to the μP during power-up,
power-down, and brownout conditions, the MAX803/
MAX809/MAX810 are relatively immune to short-duration
negative-going V
CC
transients (glitches).
Figure 1 shows typical transient duration vs. reset com-
parator overdrive, for which the MAX803/MAX809/
MAX810 do
not
generate a reset pulse. The graph was
generated using a negative-going pulse applied to V
CC
,
starting 0.5V above the actual reset threshold and end-
ing below it by the magnitude indicated (reset compara-
tor overdrive). The graph indicates the maximum pulse
width a negative-going V
CC
transient can have without
causing a reset pulse. As the magnitude of the transient
increases (goes farther below the reset threshold), the
maximum allowable pulse width decreases. Typically, for
the MAX8__L and MAX8__M, a V
CC
transient that goes
100mV below the reset threshold and lasts 20μs or less
will not cause a reset pulse. A 0.1μF bypass capacitor
mounted as close as possible to the V
CC
pin provides
additional transient immunity.
Ensuring a Valid Reset Output
Down to V
CC
= 0
When V
CC
falls below 1V, the MAX809
RESET
output
no longer sinks current—it becomes an open circuit.
Therefore, high-impedance CMOS logic inputs con-
nected to
RESET
can drift to undetermined voltages.
This presents no problem in most applications since
most μP and other circuitry is inoperative with V
CC
below 1V. However, in applications where
RESET
must
be valid down to 0V, adding a pull-down resistor to
RESET
causes any stray leakage currents to flow to
3-Pin Microprocessor Reset Circuits
R1
100k
V
CC
GND
MAX809
RESET
Figure 2.
RESET
Valid to V
CC
= Ground Circuit
2
RESET
(MAX803/
MAX809)
RESET
Output remains low while V
CC
is below the reset threshold, and for at
least 140ms after V
CC
rises above the
reset threshold.
1
GND
Ground
PIN
NAME
FUNCTION
RESET
(MAX810)
RESET Output remains high while V
CC
is below the reset threshold, and for at
least 140ms after V
CC
rises above the
reset threshold.
_____________________Pin Description
400
320
0
1
100
1000
160
80
240
RESET COMPARATOR OVERDRIVE, V
TH
- V
CC
(mV)
M
μ
s
10
T
A
= +25
°
C
MAX8_ _J/L/M
MAX8_ _R/S/T/Z
Figure 1. Maximum Transient Duration Without Causing a
Reset Pulse vs. Reset Comparator Overdrive
3
V
CC
Supply Voltage (+5V, +3.3V, +3.0V, or
+2.5V)
相關PDF資料 |
PDF描述 |
|---|---|
| MAX809J | 3-Pin Microprocessor Reset Circuits |
| MAX809L | 3-Pin Microprocessor Reset Circuits |
| MAX809M | 3-Pin Microprocessor Reset Circuits |
| MAX809R | 3-Pin Microprocessor Reset Circuits |
| MAX803L | 3-Pin Microprocessor Reset Circuits |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX810TEXR | 制造商:Maxim Integrated Products 功能描述:- Rail/Tube |
| MAX810TEXR+ | 制造商:Maxim Integrated Products 功能描述:PROCESSOR SUPERVISOR 3.08V 17UA 3PIN SC-70 - Rail/Tube |
| MAX810TEXR+T | 功能描述:監控電路 3-Pin MPU Supervisor RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| MAX810TEXR+T10 | 功能描述:監控電路 3-Pin MPU Supervisor RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| MAX810TEXR-T | 功能描述:監控電路 RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。