參數資料
型號: MAX808MCSA
廠商: MAXIM INTEGRATED PRODUCTS INC
元件分類: 電源管理
英文描述: Interface IC
中文描述: 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8
封裝: 0.150 INCH, SO-8
文件頁數: 12/12頁
文件大?。?/td> 91K
代理商: MAX808MCSA
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
12
__________________Maxim Integrated Produc ts, 120 S an Gabriel Drive, S unnyvale, CA 94086 (408) 737-7600
1996 Maxim Integrated Products
Printed USA
is a registered trademark of Maxim Integrated Products.
M
8-Pin μP S upervisory Circ uits
with ±1.5% Reset Ac c urac y
Watc hdog S oftware Considerations
To help the watchdog timer keep a closer watch on
software execution, you can set and reset the watch-
dog input at different points in the program, rather than
“pulsing” the watchdog input high-low-high or low-high-
low. This technique avoids a “stuck” loop, where the
watchdog timer continues to be reset within the loop,
keeping the watchdog from timing out.
Figure 9 shows a sample flow diagram where the I/O
driving the watchdog input is set high at the beginning
of the program, low at the beginning of every subrou-
tine or loop, then high again when the program returns
to the beginning. If the program should “hang” in any
subroutine, the I/O would be continually set low and the
watchdog timer would be allowed to time out, causing a
reset or interrupt to be issued.
Maximum V
CC
Fall T ime
The V
CC
fall time is limited by the propagation delay of
the battery switchover comparator and should not
exceed 0.03V/μs. A standard rule for filter capacitance
on most regulators is around 100μF per Ampere of cur-
rent. When the power supply is shut off or the main bat-
tery is disconnected, the associated initial V
CC
fall rate
is just the inverse, or 1A/100μF = 0.01V/μs.
START
SET
WDI
LOW
SUBROUTINE
OR PROGRAM LOOP,
SET WDI
HIGH
RETURN
END
Figure 9. Watchdog Flow Diagram
_________________Pin Configurations
WDI
RESET
RESET
GND
1
2
8
7
OUT
BATT
LOWLINE
V
CC
MAX801
DIP/SO
3
4
6
5
CE IN
RESET
CE OUT
GND
1
2
8
7
OUT
BATT
LOWLINE
V
CC
MAX808
DIP/SO
TOP VIEW
3
4
6
5
___________________Chip Information
TRANSISTOR COUNT: 922
相關PDF資料
PDF描述
MAX808MEPA Interface IC
MAX808MESA Interface IC
MAX808MMJA Interface IC
MAX808N 8-Pin &#181.P Supervisory Circuits with &#177.1.5&#37. Reset Accuracy
MAX801NCPA Interface IC
相關代理商/技術參數
參數描述
MAX808MCSA+ 功能描述:監控電路 8-Pin uPower Supervisor RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲(典型值):10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel
MAX808MCSA+T 功能描述:監控電路 8-Pin uPower Supervisor RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲(典型值):10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel
MAX808MCSA-T 功能描述:監控電路 RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲(典型值):10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel
MAX808MEPA 功能描述:監控電路 RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲(典型值):10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel
MAX808MEPA+ 功能描述:監控電路 8-Pin uPower Supervisor RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲(典型值):10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel