- 您現在的位置：買賣IC網 > PDF目錄384704 > MAX803TEXR-T (MAXIM INTEGRATED PRODUCTS INC) 3-Pin Microprocessor Reset Circuits PDF資料下載
參數資料
| 型號： | MAX803TEXR-T |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 電源管理 |
| 英文描述： | 3-Pin Microprocessor Reset Circuits |
| 中文描述： | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO3 |
| 封裝： | SC-70, 3 PIN |
| 文件頁數： | 4/8頁 |
| 文件大小： | 61K |
| 代理商： | MAX803TEXR-T |
V. Quality Assurance Information
A. Quality Assurance Contacts: Jim Pedicord (Reliability Lab Manager)
Bryan Preeshl
Kenneth Huening (Vice President)
B. Outgoing Inspection Level: 0.1% for all electrical parameters guaranteed by the Datasheet.
0.1% For all Visual Defects.
C. Observed Outgoing Defect Rate: < 50 ppm
D. Sampling Plan: Mil-Std-105D
VI. Reliability Evaluation
A. Accelerated Life Test
The results of the 135
°
C biased (static) life test are shown in
Table 1
. Using these results, the Failure
Rate (
λ
) is calculated as follows:
λ
= 1 = 1.83 (Chi square value for MTTF upper limit)
MTTF
192 x 4389 x 400 x 2
Temperature Acceleration factor assuming an activation energy of 0.8eV
λ
= 2.71 x 10
-9
λ
= 2.71 F.I.T. (60% confidence level @ 25
°
C)
This low failure rate represents data collected from Maxim’s reliability qualification and monitor programs.
Maxim also performs weekly Burn-In on samples from production to assure reliability of its processes. The
reliability required for lots which receive a burn-in qualification is 59 F.I.T. at a 60% confidence level, which equates
to 3 failures in an 80 piece sample. Maxim performs failure analysis on rejects from lots exceeding this level. The
attached Burn-In Schematic (Spec. # 06-5033) shows the static circuit used for this test. Maxim also performs
1000 hour life test monitors quarterly for each process. This data is published in the Product Reliability Report (
RR-
1M
).
B. Moisture Resistance Tests
Maxim evaluates pressure pot stress from every assembly process during qualification of each new design.
Pressure Pot testing must pass a 20% LTPD for acceptance. Additionally, industry standard 85
°
C/85%RH or
HAST tests are performed quarterly per device/package family.
C. E.S.D. and Latch-Up Testing
The MS42-2 die type has been found to have all pins able to withstand a transient pulse of
±
800V, per Mil-
Std-883 Method 3015 (reference attached ESD Test Circuit). Latch-Up testing has shown that this device
withstands a current of
±
250mA and/or
±
20V.
(Executive Director of QA)
相關PDF資料 |
PDF描述 |
|---|---|
| MAX803SEXR-T | 3-Pin Microprocessor Reset Circuits |
| MAX803SEXR-T10 | Coaxial switch for checking (Halogen free); HRS No: 358-0170-2 00; Connector Type: Adapter; Contact Gender: Male; Impedance (ohm): 50; Frequency Range (GHz): 0 to 6; Power Capacity (W): 2; VSWR (Max): 1.8; Mating/Unmating Cycles: 500; Contact Mating Area Plating: Gold; Operating Temperature Range (degrees C): -40 to 85 |
| MAX803MEXR-T | 3-Pin Microprocessor Reset Circuits |
| MAX803LEXR-T | 3-Pin Microprocessor Reset Circuits |
| MAX803R | 3-Pin Microprocessor Reset Circuits |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX803TEXR-T10 | 功能描述:監控電路 RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| MAX803Z | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:3-Pin Microprocessor Reset Circuits |
| MAX803ZEXR | 制造商:Maxim Integrated Products 功能描述:3 PIN SC70 MICROPROCESSOR RESET CIR - Rail/Tube |
| MAX803ZEXR+ | 制造商:Maxim Integrated Products 功能描述:PROCESSOR SUPERVISOR 2.32V 17UA 3PIN SC-70 - Rail/Tube |
| MAX803ZEXR+T | 功能描述:監控電路 3-Pin MPU Supervisor RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。