- 您現在的位置：買賣IC網 > PDF目錄384701 > MAX754CSE (MAXIM INTEGRATED PRODUCTS INC) Dual 2-Line To 4-Line Decoders/Demultiplexers 16-CDIP -55 to 125 PDF資料下載
參數資料
| 型號： | MAX754CSE |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 穩壓器 |
| 英文描述： | Dual 2-Line To 4-Line Decoders/Demultiplexers 16-CDIP -55 to 125 |
| 中文描述： | FLUORESCENT LIGHT CONTROLLER, 80 kHz SWITCHING FREQ-MAX, PDSO16 |
| 封裝： | SOP-16 |
| 文件頁數： | 4/16頁 |
| 文件大?。?/td> | 103K |
| 代理商： | MAX754CSE |
M
CCFL Bac klight and
LCD Contrast Controllers
4
_______________________________________________________________________________________
______________________________________________________________Pin Desc ription
Output of the CCFT Error Amplifier
CC
9
Connect to V
DD
CS
10
Leave unconnected
CDRV
11
Power Ground Connection for LDRV
PGND
12
Gate-Driver Output. Drives LCD backplane N-channel MOSFET.
LDRV
13
Digital Input for CCFT Brightness Adjustment. See Table 1.
CADJ
5
Analog Ground
GND
6
Reference Voltage Output, 1.25V
REF
7
Inverting Input for the CCFT Error Amplifier
CFB
8
Digital Input to Control CCFT Section. See Table 1.
CON
4
Digital Input to Control LCD Bias Section. See Table 1.
LON
3
PIN
Digital Input for LCD Backplane Bias Adjustment. See Table 1.
LADJ
2
5V Power-Supply Input
V
DD
1
FUNCTION
NAME
LCD Backplane Inductor Voltage-Sense Pin. Used to sense inductor voltage for on time determination.
LX
14
Battery Connection. Used to sense battery voltage for on time determination.
BATT
15
Voltage Feedback for the LCD Backplane Section
LFB
16
_______________T heory of Operation
CCFL Inverter
The MAX753/MAX754’s CCFL inverter is designed to
drive one or two cold-cathode fluorescent lamps
(CCFLs) with power levels from 100mW to 6W. These
lamps commonly provide backlighting for LCD panels
in portable computers.
Drive Requirements for CCFL Tubes
CCFL backlights require a high-voltage, adjustable AC
power source. The MAX753/MAX754 generate this AC
waveform with a self-oscillating, current-fed, parallel
resonant circuit, also known as a Royer-type oscillator.
Figure 1 shows one such circuit. The Royer oscillator is
comprised of T1, C9, the load at the secondary, Q4,
and Q5. The circuit self-oscillates at a frequency deter-
mined by the effective primary inductance and capaci-
tance. Q4 and Q5 are self-driven by the extra winding.
The current source feeding the Royer oscillator is com-
prised of L1, D5, and the MAX758A. When current from
the current source increases, so does the lamp current.
The lamp current is half-wave rectified by D7A and
D7B, and forms a voltage across resistor R8. The
MAX753’s error amplifier compares the average of this
voltage to the output of its internal DAC. Adjusting the
DAC output from zero scale to full scale (digital control)
causes the error amplifier to vary the tube current from
a minimum to a maximum. The DAC’s transfer function
is shown in Figure 2.
On power-up or after a reset, the counter sets the DAC
output to mid scale. Each rising edge of CADJ (with
CON high) decrements the DAC output. When decre-
mented beyond full scale, the counter rolls over and
sets the DAC to the maximum value. In this way, a sin-
gle pulse applied to CADJ decreases the DAC set-
point by one step, and 31 pulses increase the set-point
by one step.
The error amplifier’s output voltage controls the peak
current output of the MAX758A. The peak switch cur-
rent is therefore controlled by the output of the error
amplifier. The lower the error amplifier’s output, the
lower the peak current. Since the current through the
current source is related to the current through the
tube, the lower the error amplifier’s output, the lower the
tube current.
相關PDF資料 |
PDF描述 |
|---|---|
| MAX754EPE | Dual 2-Line To 4-Line Decoders/Demultiplexers 20-LCCC -55 to 125 |
| MAX754ESE | Dual 2-Line To 4-Line Decoders/Demultiplexers 16-CDIP -55 to 125 |
| MAX757CPA | 10-Line To 4-Line And 8-Line To 3-Line Priority Encoders 16-CDIP -55 to 125 |
| MAX756-MAX757 | 3.3V/5V/Adjustable-Output, Step-Up DC-DC Converters |
| MAX756EPA | 3.3V/5V/Adjustable-Output, Step-Up DC-DC Converters |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX754CSE+ | 制造商:Maxim Integrated Products 功能描述:- Rail/Tube |
| MAX754CSE-T | 功能描述:顯示驅動器和控制器 RoHS:否 制造商:Panasonic Electronic Components 工作電源電壓:2.7 V to 5.5 V 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:QFN-44 封裝:Reel |
| MAX754EPE | 功能描述:顯示驅動器和控制器 RoHS:否 制造商:Panasonic Electronic Components 工作電源電壓:2.7 V to 5.5 V 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:QFN-44 封裝:Reel |
| MAX754EPE+ | 制造商:Maxim Integrated Products 功能描述:- Rail/Tube |
| MAX754ESE | 功能描述:顯示驅動器和控制器 RoHS:否 制造商:Panasonic Electronic Components 工作電源電壓:2.7 V to 5.5 V 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:QFN-44 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。