- 您現在的位置：買賣IC網 > PDF目錄385549 > MAX754 (Maxim Integrated Products, Inc.) CCFL Backlight and LCD Contrast Controllers(CCFT背光和液晶顯示器對比度控制器（電源）) PDF資料下載
參數資料
| 型號： | MAX754 |
| 廠商： | Maxim Integrated Products, Inc. |
| 英文描述： | CCFL Backlight and LCD Contrast Controllers(CCFT背光和液晶顯示器對比度控制器（電源）) |
| 中文描述： | CCFL背光燈及LCD對比度控制負壓控制器 |
| 文件頁數： | 9/16頁 |
| 文件大?。?/td> | 137K |
| 代理商： | MAX754 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁
M
CCFL Bac klight and
LCD Contrast Controllers
_______________________________________________________________________________________
9
Table 1. CCFL Circuit Component Descriptions (continued)
ITEM
DESCRIPTION
C10
The ballast capacitor linearizes the CCFL impedance and guarantees no DC current through the lamp. 15pF
will work with just about any lamp. Depending on the lamp, you can try higher values, but this may cause the
regulation loop to become unstable. Larger values of C10 allow the circuit to operate with lower input volt-
ages. Don’t forget that C10 must be a high-voltage capacitor and cannot be polarized. A lamp with a
1500V
RMS
maximum strike voltage will require C10 to withstand 1500 x
√
2 = 2121V.
T1
T1 must have high primary inductance (greater than 30μH), otherwise an inflated value of C9 will be required
in order to keep the Royer frequency below 60kHz (the maximum allowed by most lamps). A higher T1 sec-
ondary-to-primary turns ratio allows lower-voltage operation, but increases the size of the transformer.
C9
You must select a value for C9 high enough to keep the lamp current reasonably sinusoidal and yet low
enough that T1’s core does not saturate. For the Sumida EPS207 with a 171:1 turns ratio, choose a 0.22μF
value for C9. The characteristic impedance of the resonant tank equals
netizing inductance of T1. The characteristic impedance is defined as the ratio of the voltage across the par-
allel LC circuit divided by the current flowing between the inductor and capacitor. This circulating current is
not delivered to the load. If C9 has too large a value, it will cause excessive circulating currents, which will in
turn saturate the core of T1. It’s easy to tell when you have excess circulating current in the resonant tank,
because when you touch T1 you burn your finger. However, reducing the value of C9 decreases tank Q,
which increases the harmonic content of the lamp-current waveform. If the lamp-current waveform does not
look sinusoidal, then the circuit may not regulate to the right root mean square current.
, where L
MAG
is the mag-
L
C
MAG
9
R10
R10 sets the base current for Q4 and Q5. If you choose too large a value for R10, Q4 and Q5 will overheat.
Too small a value will waste base current and slightly degrade efficiency. The optimal value will depend on
how much power you are trying to deliver to the lamp. 510
is a good “always works but may not be the most
efficient” value for use with the FMMT619 transistors from ZETEX.
R5, R6
This resistive divider senses the voltage at the center tap of T1. When the CC pin on the MAX758A rises
above 1.25V, the internal switch turns off, interrupting power to the Royer oscillator and limiting the open-lamp
transformer center-tap voltage.
D6B, C7, R7
D6B, C7, and R7 form a soft-start clamp, which limits the rate-of-rise of the peak current in the MAX758A.
Make sure R7 is at least 100k
so it does not excessively load the CC pin.
D6A, R17
D6A and R17 are also part of the soft-start clamp. The voltage on the SS pin controls the peak current in the
MAX758A’s switch. Make sure R17 is at least 100k
so it does not excessively load the CC pin.
L1
Inductor for the Switching-Current Source. Use a 47μH to 150μH inductor with a 1A to 1.5A saturation current.
D5
Schottky Catch Diode. Use a 1A to 1.5A Schottky diode with low forward-voltage power.
C2
Supply Bypass Capacitor. Use low-ESR capacitor.
相關PDF資料 |
PDF描述 |
|---|---|
| MAX756 | 3.3V/5V/Adjustable-Output, Step-Up DC-DC Converters(可調,高效率,步升DC-DC變換器) |
| MAX757 | 3.3V/5V/Adjustable-Output, Step-Up DC-DC Converters(可調,高效率,步升DC-DC變換器) |
| MAX7572 | Complete High Speed CMOS 12Bits ADC(單通道，3μs,帶基準源12位ADC) |
| MAX162 | CMOS 12Bits ADC(單通道，5μs,帶基準源12位ADC) |
| MAX7581 | CMOS 8Bits 8 Channel DAS(CMOS 8 位8通道數據采集系統) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX-754-1205AP | 功能描述:線性和開關式電源 MAX750 SERIES MULTI OUTPT PWR SUPPLY 12V RoHS:否 制造商:TDK-Lambda 產品:Switching Supplies 開放式框架/封閉式:Enclosed 輸出功率額定值:800 W 輸入電壓:85 VAC to 265 VAC 輸出端數量:1 輸出電壓（通道 1）:20 V 輸出電流（通道 1）:40 A 商用/醫用: 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:Rack 長度: 寬度: 高度: |
| MAX-754-1205G | 功能描述:PWR/PWR SUPPLY QUAD OUTPUT 750W RoHS:是 類別:電源 - 外部/內部（非板載） >> AC DC 轉換器 系列:MAX-750 產品培訓模塊:MP Modular-Configurable AC-DC Power Supply 特色產品:Configurable Power Supplies 標準包裝:1 系列:MP |
| MAX-754-1205P | 制造商:SLPOWER 制造商全稱:SL Power Electronics 功能描述:MAX-750 Multiple Output |
| MAX-754-1252 | 制造商:SLPOWER 制造商全稱:SL Power Electronics 功能描述:700, 750 WATTS MULTIPLE OUTPUT |
| MAX7545AKCWP | 制造商:Maxim Integrated Products 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。