- 您現在的位置：買賣IC網 > PDF目錄384700 > MAX7480EPA (MAXIM INTEGRATED PRODUCTS INC) Parallel-Load 8-Bit Shift Registers 16-CDIP -55 to 125 PDF資料下載
參數資料
| 型號： | MAX7480EPA |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 運動控制電子 |
| 英文描述： | Parallel-Load 8-Bit Shift Registers 16-CDIP -55 to 125 |
| 中文描述： | SWITCHED CAPACITOR FILTER, BUTTERWORTH, LOWPASS, PDIP8 |
| 封裝： | PLASTIC, DIP-8 |
| 文件頁數： | 7/8頁 |
| 文件大小： | 87K |
| 代理商： | MAX7480EPA |
M
8th-Order, Lowpass, Butterworth,
S witc hed-Capac itor Filter
_______________________________________________________________________________________
7
Clock Signal
External Clock
The MAX7480 SCF is designed for use with external
clocks that have a 40% to 60% duty cycle. When using
an external clock with these devices, drive CLK with a
CMOS gate powered from 0 to V
DD
. Varying the rate of
the external clock adjusts the corner frequency of the
filter as follows:
f
C
= f
CLK
/ 100
Internal Clock
When using the internal oscillator, connect a capacitor
(C
OSC
) between CLK and ground. The value of the
capacitor determines the oscillator frequency as follows:
Minimize the stray capacitance at CLK so that it does
not affect the internal oscillator frequency. Vary the rate
of the internal oscillator to adjust the filter’s corner fre-
quency by a 100:1 clock to corner-frequency ratio. For
example, an internal oscillator frequency of 100kHz
produces a nominal corner frequency of 1kHz.
Input Impedance vs. Clock Frequencies
The MAX7480’s input impedance is effectively that of a
switched-capacitor resistor, and is inversely proportion-
al to frequency. The input impedance values deter-
mined below represent the average input impedance,
since the input current is not continuous. As a rule, use
a driver with an output impedance less than 10% of the
filter’s input impedance. Estimate the input impedance
of the filter using the following formula:
where f
CLK
= clock frequency and C
IN
= 2.31pF.
Low-Power Shutdown Mode
This device features a shutdown mode that is activated
by driving
SHDN
low. In shutdown mode, the filter’s sup-
ply current reduces to 0.2μA (typ) and its output
becomes high impedance. For normal operation, drive
SHDN
high or connect to V
DD
.
___________Applications Information
Offset and Common-Mode
Input Adjustment
The voltage at COM sets the common-mode input volt-
age and is biased at mid-supply with an internal resis-
tor-divider. Bypass COM with a 0.1μF capacitor and
connect OS to COM. For applications requiring offset
adjustment or DC level shifting, apply an external bias
voltage through a resistor-divider network to OS, as
shown in Figure 3. (Note: Do not leave OS unconnect-
ed.) The output voltage is represented by this equation:
V
OUT
= (V
IN
- V
COM
) + V
OS
with V
COM
= V
DD
/ 2 (typical), where (V
IN
- V
COM
) is
lowpass-filtered by the SCF and VOS is added at the
output stage. See the Electrical Characteristics for the
voltage range of COM and OS. Changing the voltage
on COM or OS significantly from mid-supply reduces
the filter’s dynamic range.
Power Supplies
The MAX7480 operates from a single +5V supply.
Bypass V
DD
to GND with a 0.1μF capacitor. If dual
supplies (±2.5V) are required, connect COM to system
ground and connect GND to the negative supply.
Figure 4 shows an example of dual-supply operation.
Single- and dual-supply performances are equivalent.
For either single- or dual-supply operation, drive CLK
and
SHDN
from GND (V- in dual-supply operation) to
V
DD
. For ±5V dual-supply applications, use the
MAX291–MAX297.
Input Signal Amplitude Range
The optimal input signal range is determined by observ-
ing the voltage level at which the total harmonic distor-
tion plus noise (THD+N) is minimized for a given corner
frequency. The Typical Operating Characteristics
shows a graph of the device’s THD+N response as the
input signal’s peak-to-peak amplitude is varied. This
measurement is made with OS and COM biased at mid-
supply.
Z
1
C
f
IN
CLK
IN
=
(
)
f
(kHz)
C
; C
in pF
OSC
3
OSC
OSC
=
53 10
V
DD
V
SUPPLY
IN
CLK
GND
INPUT
OUTPUT
50k
50k
50k
OUT
COM
0.1
μ
F
0.1
μ
F
0.1
μ
F
CLOCK
SHDN
OS
MAX7480
Figure 3. Offset Adjustment Circuit
相關PDF資料 |
PDF描述 |
|---|---|
| MAX7480ESA | Parallel-Load 8-Bit Shift Registers 16-CFP -55 to 125 |
| MAX748A | Synchronous 4-Bit Up/Down Binary Counters 20-LCCC -55 to 125 |
| MAX748AEWE | Circular Connector; No. of Contacts:26; Series:MS27467; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:17; Circular Contact Gender:Socket; Circular Shell Style:Straight Plug; Insert Arrangement:17-26 RoHS Compliant: No |
| MAX763ACPA | 3.3V, Step-Down, Current-Mode PWM DC-DC Converters |
| MAX763ACSA | 3.3V, Step-Down, Current-Mode PWM DC-DC Converters |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX7480EPA+ | 功能描述:有源濾波器 8th-Order Lowpass Butterworth RoHS:否 制造商:Maxim Integrated 通道數量:1 截止頻率:150 KHz 電源電壓-最大:11 V 電源電壓-最小:4.74 V 最大工作溫度:+ 85 C 安裝風格:Through Hole 封裝 / 箱體:PDIP N 封裝:Tube |
| MAX7480ESA | 功能描述:有源濾波器 RoHS:否 制造商:Maxim Integrated 通道數量:1 截止頻率:150 KHz 電源電壓-最大:11 V 電源電壓-最小:4.74 V 最大工作溫度:+ 85 C 安裝風格:Through Hole 封裝 / 箱體:PDIP N 封裝:Tube |
| MAX7480ESA+ | 功能描述:有源濾波器 8th-Order Lowpass Butterworth RoHS:否 制造商:Maxim Integrated 通道數量:1 截止頻率:150 KHz 電源電壓-最大:11 V 電源電壓-最小:4.74 V 最大工作溫度:+ 85 C 安裝風格:Through Hole 封裝 / 箱體:PDIP N 封裝:Tube |
| MAX7480ESA+T | 功能描述:有源濾波器 8th-Order Lowpass Butterworth RoHS:否 制造商:Maxim Integrated 通道數量:1 截止頻率:150 KHz 電源電壓-最大:11 V 電源電壓-最小:4.74 V 最大工作溫度:+ 85 C 安裝風格:Through Hole 封裝 / 箱體:PDIP N 封裝:Tube |
| MAX7480ESA-T | 功能描述:有源濾波器 RoHS:否 制造商:Maxim Integrated 通道數量:1 截止頻率:150 KHz 電源電壓-最大:11 V 電源電壓-最小:4.74 V 最大工作溫度:+ 85 C 安裝風格:Through Hole 封裝 / 箱體:PDIP N 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。