- 您現在的位置：買賣IC網 > PDF目錄384700 > MAX747MJD (MAXIM INTEGRATED PRODUCTS INC) Parallel-Load 8-Bit Shift Registers 16-CDIP -55 to 125 PDF資料下載
參數資料
| 型號： | MAX747MJD |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 穩壓器 |
| 英文描述： | Parallel-Load 8-Bit Shift Registers 16-CDIP -55 to 125 |
| 中文描述： | SWITCHING CONTROLLER, 100 kHz SWITCHING FREQ-MAX, CDIP14 |
| 封裝： | CERDIP-14 |
| 文件頁數： | 8/12頁 |
| 文件大?。?/td> | 136K |
| 代理商： | MAX747MJD |
With decreasing loads, as the inductor current becomes
discontinuous, traditional PWM converters continue to
switch at a fixed frequency, decreasing light-load efficiency.
However, the MAX747’s idle-mode comparator increases
the peak inductor current, allowing more energy to be
transferred per cycle. Since fewer cycles are required, the
switching frequency is reduced. This keeps the external P-
FET off for longer periods, minimizing switching losses and
increasing efficiency.
The light-load output noise spectrum widens due to variable
switching frequency in idle-mode, but output ripple remains
low. Using the Typical Operating Circuit with a 9V input and
a 125mA load current, output ripple is less than 40mV.
S oft-S tart and Current Limiting
T
he MAX747 draws its highest current at power-up. If The
power source to the MAX747 cannot provide this initial
elevated current, the circuit may not function correctly. For
example, after prolonged use, a battery’s increased series
resistance may prevent it from providing adequate initial
surge currents when the MAX747 is brought out of
shutdown. Using Soft-Start (SS) minimizes the possibility of
overloading the incoming supply at power-up by gradually
increasing the peak current limit. Connect an external
capacitor from SS to ground to reduce the initial peak
currents drawn from the supply.
The steady-state SS pin voltage is typically 3.8V. On
power-up, SS sources 1μA until the SS voltage reaches
3.8V. The current-limit comparator inhibits EXT switching
until the SS voltage reaches 1.8V. The maximum current
limit is set by:
V
R
R
SENSE
SENSE
Figure 3 shows how the peak current limit increases as
the voltage on SS rises for two R
SENSE
values.
S hutdown Mode
When SHDN is high, the MAX747 enters shutdown
mode. In this mode, the internal biasing circuitry
(including EXT) is turned off, V
drops to 0V, and the
supply current drops to 0.6μA (20μA max). This
excludes external component leakage, which may add
several microamps to the shutdown supply current for
the entire circuit. SHDN is a TTL/CMOS logic-level
input. Connect SHDN to GND for normal operation.
Low-Battery Detec tor
The MAX747 provides a low-battery comparator that
compares the voltage on LBI to the reference voltage.
LBO, an open-drain output, goes low when the LBI
voltage is below V
. Use a resistor-divider network
as shown in Figure 4 to set the trip voltage (V
) to
the desired level. In this circuit, LBO goes low when
V+
≤
V
TRIP
. LBO is high impedance in shutdown mode.
__________________Design Proc edure
S etting the Output V oltage
The MAX747’s output voltage can be set to 5V by
grounding FB, or adjusted from 2V to 14V using
external resistors R4 and R5, configured as shown in
Figure 5. Select feedback resistor R4 from the 10k
to
1M
range. R5 is given by:
V
2V
S elec ting R
S ENS E
First, approximate the peak current assuming I
is
(1.1)(I
), where I
is the maximum load current.
Once all component values have been determined, the
actual peak current is given by:
Next, determine the value of R
SENSE
such that:
V
SENSE
PK
For example, to obtain 5V at 3A, I
PK
= 3.3A and R
SENSE
=
125mV/3.3A = 38m
.
The sense resistor should have a power rating greater
than (I
PK2
)(R
) (with an adequate safety margin).
With a 3A load current, I
= 3.3A and R
= 38m
.
The power dissipated by the resistor (assuming an 80%
R
I
125mV
I
PK
LIMIT (MIN)
=
=
I
I
V
(2L) (f
)
1
V
V
PK
LOAD
OUT
OSC
OUT
IN
=
+
R5
(R4)
1
OUT
=
I
150mV (typ)
PK
LIMIT
=
=
M
High-Effic ienc y PWM, S tep-Down
P-Channel DC-DC Controller
8
_______________________________________________________________________________________
0
M
SOFT-START VOLTAGE (V)
P
4
2
1
1
3
3
2
0
R
SENSE
= 50m
R
SENSE
= 100m
V+ –V
CS
= 150mV
Figure 3. Peak Current Limit vs. Soft-Start Voltage
相關PDF資料 |
PDF描述 |
|---|---|
| MAX7480 | Parallel-Load 8-Bit Shift Registers 20-LCCC -55 to 125 |
| MAX7480EPA | Parallel-Load 8-Bit Shift Registers 16-CDIP -55 to 125 |
| MAX7480ESA | Parallel-Load 8-Bit Shift Registers 16-CFP -55 to 125 |
| MAX748A | Synchronous 4-Bit Up/Down Binary Counters 20-LCCC -55 to 125 |
| MAX748AEWE | Circular Connector; No. of Contacts:26; Series:MS27467; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:17; Circular Contact Gender:Socket; Circular Shell Style:Straight Plug; Insert Arrangement:17-26 RoHS Compliant: No |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX7480EPA | 功能描述:有源濾波器 RoHS:否 制造商:Maxim Integrated 通道數量:1 截止頻率:150 KHz 電源電壓-最大:11 V 電源電壓-最小:4.74 V 最大工作溫度:+ 85 C 安裝風格:Through Hole 封裝 / 箱體:PDIP N 封裝:Tube |
| MAX7480EPA+ | 功能描述:有源濾波器 8th-Order Lowpass Butterworth RoHS:否 制造商:Maxim Integrated 通道數量:1 截止頻率:150 KHz 電源電壓-最大:11 V 電源電壓-最小:4.74 V 最大工作溫度:+ 85 C 安裝風格:Through Hole 封裝 / 箱體:PDIP N 封裝:Tube |
| MAX7480ESA | 功能描述:有源濾波器 RoHS:否 制造商:Maxim Integrated 通道數量:1 截止頻率:150 KHz 電源電壓-最大:11 V 電源電壓-最小:4.74 V 最大工作溫度:+ 85 C 安裝風格:Through Hole 封裝 / 箱體:PDIP N 封裝:Tube |
| MAX7480ESA+ | 功能描述:有源濾波器 8th-Order Lowpass Butterworth RoHS:否 制造商:Maxim Integrated 通道數量:1 截止頻率:150 KHz 電源電壓-最大:11 V 電源電壓-最小:4.74 V 最大工作溫度:+ 85 C 安裝風格:Through Hole 封裝 / 箱體:PDIP N 封裝:Tube |
| MAX7480ESA+T | 功能描述:有源濾波器 8th-Order Lowpass Butterworth RoHS:否 制造商:Maxim Integrated 通道數量:1 截止頻率:150 KHz 電源電壓-最大:11 V 電源電壓-最小:4.74 V 最大工作溫度:+ 85 C 安裝風格:Through Hole 封裝 / 箱體:PDIP N 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。