- 您現在的位置：買賣IC網 > PDF目錄11016 > MAX7405ESA+ (Maxim Integrated Products)IC FILTER LOWPASS 8-SOIC PDF資料下載
參數資料
MAX7401/MAX7405
8th-Order, Lowpass, Bessel,
Switched-Capacitor Filters
_______________________________________________________________________________________
9
GND to the negative supply. Figure 4 shows an example
of dual-supply operation. Single- and dual-supply perfor-
mance are equivalent. For either single- or dual-supply
operation, drive CLK and SHDN from GND (V- in dual-
supply operation) to VDD. For ±5V dual-supply applica-
tions, use the MAX291–MAX297.
Input Signal Amplitude Range
The optimal input signal range is determined by observ-
ing the voltage level at which the total harmonic distor-
tion plus noise (THD+N) is minimized for a given corner
frequency. The
Typical Operating Characteristics show
graphs of the devices’ THD+N response as the input
signal’s peak-to-peak amplitude is varied. These mea-
surements are made with OS and COM biased at mid-
supply.
Anti-Aliasing and Post-DAC Filtering
When using the MAX7401/MAX7405 for anti-aliasing or
post-DAC filtering, synchronize the DAC and the filter
clocks. If the clocks are not synchronized, beat frequen-
cies may alias into the passband.
The high clock-to-corner frequency ratio (100:1) also
eases the requirements of pre- and post-SCF filtering. At
the input, a lowpass filter prevents the aliasing of fre-
quencies around the clock frequency into the passband.
At the output, a lowpass filter attenuates the clock
feedthrough.
A high clock-to-corner frequency ratio allows a simple
RC lowpass filter, with the cutoff frequency set above
the SCF corner frequency, to provide input anti-aliasing
and reasonable output clock attenuation.
Harmonic Distortion
Harmonic distortion arises from nonlinearities within the
filter. These nonlinearities generate harmonics when a
pure sine wave is applied to the filter input. Table 1 lists
the MAX7401/MAX7405’s typical harmonic-distortion
values with a 10k
load at TA = +25°C.
VDD
V+
V-
IN
CLK
GND
INPUT
OUTPUT
OUT
0.1
F
CLOCK
*DRIVE SHDN TO V- FOR LOW-POWER SHUTDOWN MODE.
SHDN
COM
OS
0.1
F
MAX7401
MAX7405
*
V+
V-
Figure 4. Dual-Supply Operation
5th
3rd
-92
-79
-93
-83
500
100
fCLK
(kHz)
4th
2nd
-92
-90
TYPICAL HARMONIC DISTORTION (dB)
-89
-91
4
5
1
MAX7401
VIN
(Vp-p)
fC
(kHz)
FILTER
1000
200
fIN
(Hz)
Table 1. Typical Harmonic Distortion
TRANSISTOR COUNT: 1116
Chip Information
-88
-82
-88
-83
500
100
-88
-87
-83
-87
2
5
1
MAX7405
1000
200
相關PDF資料 |
PDF描述 |
|---|---|
| MAX7430EUB+ | IC FILTER VIDEO SD 10-UMAX |
| MAX275BCWP+T | IC FILTER ACTIVE 20-SOIC |
| MAX7490EEE+T | IC FILTER SW CAP DUAL 16-QSOP |
| MAX292CSA+T | IC FILTER LOWPASS 8-SOIC |
| MAX291CSA+T | IC FILTER LOWPASS 8-SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX7405ESA+ | 功能描述:有源濾波器 8th-Order Lowpass Elliptic Filter RoHS:否 制造商:Maxim Integrated 通道數量:1 截止頻率:150 KHz 電源電壓-最大:11 V 電源電壓-最小:4.74 V 最大工作溫度:+ 85 C 安裝風格:Through Hole 封裝 / 箱體:PDIP N 封裝:Tube |
| MAX7405ESA+T | 功能描述:有源濾波器 8th-Order Lowpass Elliptic Filter RoHS:否 制造商:Maxim Integrated 通道數量:1 截止頻率:150 KHz 電源電壓-最大:11 V 電源電壓-最小:4.74 V 最大工作溫度:+ 85 C 安裝風格:Through Hole 封裝 / 箱體:PDIP N 封裝:Tube |
| MAX7405ESA-T | 功能描述:有源濾波器 RoHS:否 制造商:Maxim Integrated 通道數量:1 截止頻率:150 KHz 電源電壓-最大:11 V 電源電壓-最小:4.74 V 最大工作溫度:+ 85 C 安裝風格:Through Hole 封裝 / 箱體:PDIP N 封裝:Tube |
| MAX7407CPA | 功能描述:有源濾波器 RoHS:否 制造商:Maxim Integrated 通道數量:1 截止頻率:150 KHz 電源電壓-最大:11 V 電源電壓-最小:4.74 V 最大工作溫度:+ 85 C 安裝風格:Through Hole 封裝 / 箱體:PDIP N 封裝:Tube |
| MAX7407CPA+ | 功能描述:有源濾波器 8th-Order Lowpass Elliptic Filter RoHS:否 制造商:Maxim Integrated 通道數量:1 截止頻率:150 KHz 電源電壓-最大:11 V 電源電壓-最小:4.74 V 最大工作溫度:+ 85 C 安裝風格:Through Hole 封裝 / 箱體:PDIP N 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。