參數資料
型號： MAX7315ATE+T
廠商： Maxim Integrated Products
文件頁數： 25/26頁
文件大小： 0K
描述： IC I/O EXPANDER I2C 8B 16TQFN-EP
產品培訓模塊： Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝： 2,500
接口： I²C，SM 總線
輸入/輸出數： 8
中斷輸出： 是
頻率 - 時鐘： 400kHz
電源電壓： 2 V ~ 3.6 V
工作溫度： -40°C ~ 125°C
安裝類型： 表面貼裝
封裝/外殼： 16-WFQFN 裸露焊盤
供應商設備封裝： 16-TQFN-EP（3x3）
包裝： 帶卷 (TR)
MAX7315
only as an input. A pullup resistor, typically 4.7k
, is
required on SCL if there are multiple masters on the 2-
wire interface, or if the master in a single-master system
has an open-drain SCL output.
Each transmission consists of a START condition
(Figure 3) sent by a master, followed by the MAX7315
7-bit slave address plus R/W bit, a register address
byte, one or more data bytes, and finally a STOP condi-
tion (Figure 3).
Start and Stop Conditions
Both SCL and SDA remain high when the interface is
not busy. A master signals the beginning of a transmis-
sion with a START (S) condition by transitioning SDA
from high to low while SCL is high. When the master
has finished communicating with the slave, it issues a
STOP (P) condition by transitioning SDA from low to
high while SCL is high. The bus is then free for another
transmission (Figure 3).
Bit Transfer
One data bit is transferred during each clock pulse.
The data on SDA must remain stable while SCL is high
(Figure 4).
Acknowledge
The acknowledge bit is a clocked 9th bit that the recipi-
ent uses to handshake receipt of each byte of data
(Figure 5). Thus, each byte transferred effectively
requires 9 bits. The master generates the 9th clock
pulse, and the recipient pulls down SDA during the
acknowledge clock pulse so the SDA line is stable low
during the high period of the clock pulse. When the
master is transmitting to the MAX7315, the device gen-
erates the acknowledge bit because the MAX7315 is
the recipient. When the MAX7315 is transmitting to the
master, the master generates the acknowledge bit
because the master is the recipient.
Slave Address
The MAX7315 has a 7-bit long slave address (Figure 6).
The eighth bit following the 7-bit slave address is the
R/W bit. The R/W bit is low for a write command, high
for a read command.
The slave address bits A6 through A0 are selected by
the address inputs AD0, AD1, and AD2. These pins can
be connected to GND, V+, SDA, or SCL. The MAX7315
has 64 possible slave addresses (Table 1) and, there-
fore, a maximum of 64 MAX7315 devices can be con-
trolled independently from the same interface.
Message Format for Writing the MAX7315
A write to the MAX7315 comprises the transmission of
the MAX7315’s slave address with the R/W bit set to
zero, followed by at least 1 byte of information. The first
byte of information is the command byte. The command
byte determines which register of the MAX7315 is to be
written to by the next byte, if received (Table 2). If a
STOP condition is detected after the command byte is
received, then the MAX7315 takes no further action
beyond storing the command byte.
8-Port I/O Expander with LED Intensity
Control, Interrupt, and Hot-Insertion Protection
8
_______________________________________________________________________________________
Figure 3. Start and Stop Conditions
SDA
SCL
START
CONDITION
STOP
CONDITION
S
P
Figure 4. Bit Transfer
SDA
SCL
DATA LINE STABLE;
DATA VALID
CHANGE OF DATA
ALLOWED
Figure 5. Acknowledge
SCL
SDA BY
TRANSMITTER
CLOCK PULSE
FOR ACKNOWLEDGE
START
CONDITION
SDA BY
RECEIVER
1
2
8
9
S
Figure 6. Slave Address
SDA
SCL
A5
MSB
LSB
ACK
A4
A1
A6
A3
A0
A2
R/W
相關PDF資料
PDF描述
MAX7315AUE+T IC I/O EXPANDER I2C 8B 16TSSOP
AT90USB162-16MUR IC AVR MCU 16K FLASH 32QFN
MAX7321ATE+T IC I/O EXPANDER I2C 8B 16TQFN-EP
MAX7320AEE+T IC I/O EXPANDER I2C 8B 16QSOP
ATMEGA8U2-MUR MCU AVR 8K FLASH 16MHZ 32VQFN
相關代理商/技術參數
參數描述
MAX7315AUE 功能描述:接口-I/O擴展器 8-Bit I/O Port Expander RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel
MAX7315AUE+ 功能描述:接口-I/O擴展器 8-Bit I/O Port Expander RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel
MAX7315AUE+T 功能描述:接口-I/O擴展器 8-Bit I/O Port Expander RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel
MAX7315AUE-G05 功能描述:接口-I/O擴展器 8-Bit I/O Port Expander RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel
MAX7315AUE-T 功能描述:接口-I/O擴展器 8-Bit I/O Port Expander RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*