- 您現在的位置：買賣IC網 > PDF目錄3769 > MAX7300AAX+T (Maxim Integrated Products)IC I/O EXPANDER I2C 28B 36SSOP PDF資料下載
參數資料
| 型號： | MAX7300AAX+T |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 20/20頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC I/O EXPANDER I2C 28B 36SSOP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 1,000 |
| 接口： | I²C，2 線串口 |
| 輸入/輸出數： | 28 |
| 中斷輸出： | 是 |
| 頻率 - 時鐘： | 400kHz |
| 電源電壓： | 2.5 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 36-BSOP（0.295"，7.50mm 寬） |
| 供應商設備封裝： | 36-SSOP |
| 包裝： | 帶卷 (TR) |
MAX7300
2-Wire-Interfaced, 2.5V to 5.5V, 20-Port or
28-Port I/O Expander
_______________________________________________________________________________________
9
Any bytes received after the command byte are consid-
ered data bytes. The first data byte goes into the inter-
nal register of the MAX7300 selected by the command
byte (Figure 8). If multiple data bytes are transmitted
before a STOP condition is detected, these bytes are
generally stored in subsequent MAX7300 internal regis-
ters because the command byte address generally
autoincrements (Table 4).
Message Format for Reading
The MAX7300 is read using the MAX7300’s internally
stored command byte as address pointer, the same way
the stored command byte is used as address pointer for
a write. The pointer generally autoincrements after each
data byte is read using the same rules as for a write
(Table 4). Thus, a read is initiated by first configuring the
MAX7300’s command byte by performing a write (Figure
7). The master can now read ‘n’ consecutive bytes from
the MAX7300, with the first data byte being read from the
register addressed by the initialized command byte
(Figure 9). When performing read-after-write verification,
remember to reset the command byte’s address
because the stored control byte address generally has
been autoincremented after the write (Table 4). Table 5
is the register address map.
Figure 2. 2-Wire Serial Interface Timing Details
SCL
SDA
START CONDITION
STOP CONDITION
REPEATED START CONDITION
START CONDITION
tSU, DAT
tHD, DAT
tLOW
tHD, STA
tHIGH
tR
tF
tSU, STA
tHD, STA
tSU, STO
tBUF
Figure 3. Start and Stop Conditions
SDA
SCL
S
START
CONDITION
P
STOP
CONDITION
SDA
SCL
DATA LINE STABLE; DATA VALID CHANGE OF DATA ALLOWED
Figure 4. Bit Transfer
相關PDF資料 |
PDF描述 |
|---|---|
| PCA9698DGG,518 | IC I/O EXPANDER I2C 40B 56TSSOP |
| PCA9506DGG,518 | IC I/O EXPANDER I2C 40B 56TSSOP |
| MAX7323ATE+ | IC I/O EXPANDER I2C 4B 16TQFN-EP |
| ATMEGA48-15AT1 | MCU AVR 4K FLASH 15MHZ 32-TQFP |
| PCA9675DB,112 | IC I/O EXPANDER I2C 16B 24SSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX7300AGL | 功能描述:接口-I/O擴展器 2.5-5.5V 20/28 Port I/O Expander RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel |
| MAX7300AGL+T | 功能描述:接口-I/O擴展器 RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel |
| MAX7300AGL-T | 功能描述:接口-I/O擴展器 2.5-5.5V 20/28 Port I/O Expander RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel |
| MAX7300AGL-TG068 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| MAX7300ANI | 功能描述:接口-I/O擴展器 RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。