- 您現在的位置：買賣IC網 > PDF目錄384698 > MAX724ECK (MAXIM INTEGRATED PRODUCTS INC) Octal Buffers And Line Drivers With 3-State Outputs 20-CDIP -55 to 125 PDF資料下載
參數資料
| 型號： | MAX724ECK |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 穩壓器 |
| 英文描述： | Octal Buffers And Line Drivers With 3-State Outputs 20-CDIP -55 to 125 |
| 中文描述： | 8.5 A SWITCHING REGULATOR, 120 kHz SWITCHING FREQ-MAX, PZFM5 |
| 封裝： | TO-220, 5 PIN |
| 文件頁數： | 7/12頁 |
| 文件大?。?/td> | 92K |
| 代理商： | MAX724ECK |
M
5A/2A S tep-Down, PWM,
S witc h-Mode DC-DC Regulators
_______________________________________________________________________________________
7
Induc tor S elec tion
Although most MAX724 designs perform satisfactorily
with 50
μ
H inductors (100μH for the MAX726), the
MAX724/MAX726 are able to operate with values rang-
ing from 5
μ
H to 200
μ
H. In some cases, inductors other
than 50
μ
H may be desired to minimize size (lower
inductance), or reduce ripple (higher inductance). In
any case, inductor current must at least be rated for the
desired output current.
In high-current applications, pay particular attention to
both the RMS and peak inductor ratings. The induc-
tor's peak current is limited by core saturation.
Exceeding the saturation limit actually reduces the
coil's inductance and energy storage ability, and
increases power loss. Inductor RMS current ratings
depend on heating effects in the coil windings.
The following equation calculates maximum output cur-
rent as a function of inductance and input conditions:
V
OUT
(V
IN
- V
OUT
)
I
OUT
= I
SW
-
2 f
OSC
V
IN
L
where I
is the maximum switch current (5.5A for
MAX724), V
is the maximum input voltage, V
is the
output voltage, and f
OSC
is the switching frequency.
For the MAX724 example in Figure 2, with L = 50
μ
H
and V
IN
= 25V,
5V (25V - 5V)
2 (10
5
Hz) 25V (50 x 10
-6
H)
Note that increasing or decreasing inductor value pro-
vides only small changes in maximum output current
(100
μ
H = 5.3A, 20
μ
H = 4.5A). The equation shows that
output current is mostly a function of the
MAX724/MAX726 current-limit value. Again, a 50
μ
H
inductor works well in most applications and provides
5A with a wide range of input voltages.
I
OUT
= 5.5A -
= 5.1A
Catc h Diode
D1 provides a path for inductor current when V
turns
off. Under normal load conditions, the average diode
current may only be a fraction of load current; but dur-
ing short-circuit or current-limit, diode current is higher.
Conservative design dictates that the diode average
current rating be 2 times the desired output current. If
operation with extended short-circuit or overload time is
expected, then the diode current rating must exceed
the current limit (6.5A = MAX724, 2.6A = MAX726), and
heat sinking may be necessary.
Under normal operating conditions (not shorted), power
dissipated in the diode P
D
is calculated by:
P
D
= I
OUT
(V
IN
- V
OUT
) V
D
V
IN
where V
D
is forward drop of the diode at a current
equal to I
. In nearly all circuits, Schottky diodes
provide the best performance and are recommended
due to their fast switching times and low forward voltage
drop. Standard power rectifiers such as the 1N4000
series are too slow for DC-DC conversion circuits and are
not
recommended.
Output Filter Capac itor
For most MAX724/MAX726 applications, a high-quality,
low-ESR, 470
μ
F or 500
μ
F output filter capacitor will suf-
fice. To reduce ripple, minimize capacitor lead length
and connect the capacitor directly to the GND pin.
Capacitor suppliers are listed in Table 1. Output ripple
is a function of inductor value and output capacitor
effective series resistance (ESR). In continuous-con-
duction mode:
ESR (V
OUT
) (1 - V
OUT
/V
IN
)
V
CR(p-p)
=
L f
OSC
It is interesting to note that input voltage (V
), and not
load current, affects output ripple in CCM. This is
because only the DC, and not the peak-to-peak, induc-
tor current changes with load (see Figure 3).
In discontinuous-conduction mode, the equation is dif-
ferent because the peak-to-peak inductor current does
depend on load:
V
DR(p-p)
= ESR
√
2 I
OUT
V
OUT
(V
IN
- V
OUT
)
L f
OSC
V
IN
where output ripple is proportional to the square root of
load current. Refer to the earlier equation for I
to
determine where DCM occurs and hence when the
DCM ripple equation should be used.
Input Bypass Capac itor
An input capacitor (200
μ
F or 220
μ
F) is required for step-
down converters because the input current, rather than
being continuous (like output current), is a square wave.
For this reason the capacitor must have low ESR and a
ripple-current rating sufficiently large so that its ESR and
the AC input current do not conspire to overheat the
capacitor. In CCM, the capacitor's RMS ripple current is:
I
R(RMS)
= I
OUT
√
V
OUT
(V
IN
- V
OUT
)
V
IN2
The power dissipated in the input capacitor is then P
C
:
P
C
= I
R(RMS)2
(ESR)
相關PDF資料 |
PDF描述 |
|---|---|
| MAX724CCK | 5A/2A Step-Down, PWM, Switch-Mode DC-DC Regulators |
| MAX7319 | 4-Bit D-type Registers with 3-State Outputs 16-CFP -55 to 125 |
| MAX732 | Hex D-type Flip-Flops With Clear 16-CFP -55 to 125 |
| MAX733 | +12V/+15V Step-Up Current-Mode Pwm Regulators |
| MAX732EWE | +5V/Adjustable Step-Up Current-Mode DC-DC Converters |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX724ECK-SL | 功能描述:直流/直流開關調節器 RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5 |
| MAX724ECM | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Current-Mode SMPS Controller |
| MAX724EKS | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Current-Mode SMPS Controller |
| MAX724HC/D | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Current-Mode SMPS Controller |
| MAX724HCCK | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Current-Mode SMPS Controller |
發布緊急采購，3分鐘左右您將得到回復。